- Optomistic Products
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-...show more -
product
6TL08 Benchtop Test Platform
H710008
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
6TL10 Table Top Test Base
H71001000
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
Test Connectors
The need for contacting standard USB or RJ connections and interfaces is increasing in the field of in-circuit and functional tests of PCBs because the standardization of these interfaces has great advantages.
-
product
Test Connectors
A wide range of standard test Connectors that can fit many of your applications and services. We offer a ideal solution for your testing needs in automatic or manual mode.
-
product
PCB Test Connectors
Tag-Connect
Tag-Connect is a simple and secure way of connecting debuggers, programmers and test equipment to your PCBs. Tag-Connect uses a specially designed and patented connector for making the connection to your PCB (Patent Pending for the -NL versions). Tag-Connect eliminates the need for a programming or JTAG connector on your PCB.
-
product
Flexible Test Connectors
Pin and socket sizes 22, 20, 16, 12 and 8 conform to MIL Spec dimensions. Whenever connector reliability is important, you’ll find NASA-approved FLEXCON test connectors. Applications include electronic, electrical and communications systems, computers, space vehicles, missiles, aircraft and other military equipment.
-
product
FPC Test Connectors
FPC Test Connectors (Clip Connectors) can easily be inserted and can be used for repeat testing, saving time and money as well as minimizing damage.
-
product
Quick Test Connectors
Pressure-tight connection in seconds. Since 1980 WEH have offered an innovative range of test connectors, which can make pressure- and function-tight connections in seconds. The vast product line includes quick connectors for pressure, vacuum, function and leak testing.
-
product
Custom Test Connectors and Sockets
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
product
FPC Test Connector Clip Connectors
FPC Test Connectors (Clip Connectors) can easily be inserted and can be used for repeat testing, saving time and money as well as minimizing damage.
-
product
Test Socket Based Elastomeric Matrix Connectors
Z-Axis offers a wide range of high performance test sockets, which are based on our elastomeric matrix connectors, for wide range of IC packages (BGA sockets, LGA sockets, etc.), coaxical, and wafer level; and for testing high speed, digital, analog, and RF signals etc.
-
product
PCB Connectors
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger offers a wide range of PCB connectors, which are tailored to the high demands of industrial test applications. The product range includes many common standard RF series, e.g. SMP, WSMP, Mini-SMP, SMA, QMA, SMB, MCX or Mini-Coax, but also innovative coaxial series such as P-SMP, Longwipe-SMP, FMC or Micro-RF.For specific test & measurement applications, Rosenberger develops and produces modular connector systems for DC frequencies up to 50 GHz, solderless PCB mount connectors for ultra-high frequency applications up to 110 GHz or spring-loaded coax systems ( > 2,500 matings, pairwise phase matching 10 ps standard, different cable lengths).
-
product
Connectors Specifications
Flex to Board
This revolutionary new ‘wiping’ action RC contact technology is a Patented Ardent Solution for ultra-small flex-to-board connectors and sockets. Ideal for both test and production use, SC™ connectors are available for custom applications with short lead times. Exceptional Signal Integrity Long Life Lower Component Costs Lower Overall Costs
-
product
Rugged Connectors
Guaranteed for a minimum of 100,000 connections, our rugged connectors are designed to meet your industrial & ergonomic demands in harsh testing environments. We offer numerous connector specifications all fitted with interchangeable spring loaded test probes. Supplied as a single hand held unit, panel mounted or fitted to a test lead, the combinations are limitless. Designed directly from your CAD data and thoroughly tested, our rugged & reliable connectors are used worldwide on a daily basis.
-
product
Production Connectors
Production Connectors for the manufacturing and testing of component assemblies. Handheld Production Connectors for assembly lines. Machine Mounted Test Connectors. Part-in-Place detection.
-
product
Small I/O Connectors
APEX
APEX connectors are designed to provide optimum performance in small I/O test and measurement applications. APEX connector modules are unmatched for strength, stability and performance when compared to the typical molded plastic alternatives. APEX aluminum back shells are designed to truly withstand the rigors of real-life applications. When performance and reliability are your primary metrics, APEX is the right choice.
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large libr...show more -
product
Test Cables
Test cables for tone generators, butt sets, oscilloscopes, digital multi-meters (DMM), and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
product
Test Fixtures-Assemblies
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
product
Couplers, Repeaters, Bus Switches, Connectors, Cables & More
Accessories for the MIL-STD-1553 data bus are as much of an interface as the communication card. Therefore at Excalibur we provide a full line of accessories for the MIL-STD-1553 data bus that include, Box/Inline Couplers, Repeaters, Bus Switches, break out boxes, connectors, terminators, transformers and custom cable assemblies. Excalibur uses only premier quality parts from known manufacturers. We constantly test our products to meet our higher standards.If you have a need for an accessory product for your card and it is not listed please contact us to see if it is a product we should be supporting.
-
product
Multimeter Test Probes
Multimeter Test Probes, Voltmeter test leads,with the Parrot™ Clip Invention provide precise, HQ, accurate, reliable contacts and connections. Parrot™ Clips with HQ leads and banana plugs or other connectors are the best solution for DDM, analog multimeter for high voltage measurements as well as for high current measurements. Measurements with multimeter test probes require both: Hands-on direct point contact and grip on, Hands free removable connection.
-
product
Optical Test And Measurement
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision...show more -
product
Package Test Loadboards/DIB
DTS Package Test (DIB) loadboards are designed to specific devices and configured for both hand test and fully automated handler applications. DTS loadboards incorporate any brand of socket or contactor and can be configured for multi-site testing. Designs incorporate all necessary components, connectors, mechanical hardware and stiffeners to provide a complete plug-n-play solution. DTS has a vast database of tester and handler information which allow designs to be started and completed quickly without burdening the customer to supply excessive information. DTS designers are experienced in all device types, including digital, analog, mixed signal and RF devices.
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) typ...show more -
product
Automated Test And Measurement
Test and Measurement applications include collecting data on parts such as force, current, power, speed, torque, sound, vibration, temperature, and more that are used to compare to known design specifications or operating parameters. Typical challenges include end-of-line testing on products such as power tools, transformers, ice makers, connectors, tires, and others to confirm the product meets specified quality control requirements.
-
product
Cable-End Test Fixtures
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
product
Cable Test Box
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
product
Compression Test Apparatus
CT-20 C
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat
-
product
Connector Test Tools
Yokowo Connector Test Tools - BtoB Clips, Interface Connectors, and Tools for FPC Connectors
-
product
Test Connector Components
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
