Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, SC/PC Connectors, With Interlock
42-860A-222-HI
The 40/42-860A-222-HI is a PXI/PXIe dual insert/bypass switch with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Automated Optical Switch - PXI
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
product
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1.5m
150275-1R5
96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1.5m - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.
-
product
PXI Solid State Switch Module, 3xSPST, 10 A
40-182A-012
The 40-182A-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
20-Channel Actuator / GP Switch Module for DAQ970A and DAQ973A
DAQM903A
DAQM903A 20 Channel Actuator/GP Switch Module for DAQ970A and DAQ973A. 20 independent single-pole, double-throw (SPDT) relays with switching voltage up to 300 V.
-
product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-904-HI
The 65-233-904-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Remote Switch Probe
U5404A
This 18 mm test probe is highly recommended for CAT IV environment and is compatible with the U1281A/82A handheld DMMs
-
product
PXI/PXIe RF Switch, 8xSP4T + 4xSP4T, 1.3 GHz, 50 Ω, Multiway Connectors
40-755A-902
The 40-755A-902 (PXI) and 42-755A-902 (PXIe) are high density RF switch modules configured as 8xSP4T and 4xSPDT. The range of modules is available in 50 Ω and 75 Ω variants with mixed SP4T & SPDT switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 40 GHz, 50 Ω, SMA-2.9, Failsafe, Remote Mount
40-782B-541-E
The 40-782B-541-E (PXI) and 42-782B-541-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI/PXIe RF Switch, Hex SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-003
The 40-880B-003 (PXI) and 42-880B-003 (PXIe) are hex SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in slots or hex and octal switches in three slots.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
Switching Regulators
Renesas offers a wide range of high performance switching regulators that operate with both synchronous and non-synchronous internal switches (FETs).
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
Multifunction Switch / Measure Unit, Modules
34980A Series
The Keysight 34980A multifunction switch / measure mainframe and modules provide functionality that is easy to set up and use. The 34980A helps you lower your cost of test and accelerate your test system integration and development.
-
product
Coded Switches
Elma's coded switches provide a high-quality tactile feedback. The standard 10, 16 and 24 position the concentric designs as well are used extensively as frequency selectors, medical device interfaces, audio attenuators and industrial controls. Elma can also customize shafts, bushings and switching schemes to meet special applications.
-
product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
product
Public Switch Telephone Network Tester
295B
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
product
SS Body Pressure Switch (longbody, NEMA 4)
P117LG
The P117LG NEMA 4 Stainless Steel Pressure Switches are the weather-proof, liquid-resistant version of the P117G. The NEMA 4 rating makes these rugged switches suitable for outside applications or in areas of condensing humidity. Unlike the P117G, the P117LG set point is factory set to customer specification and is non-adjustable.
-
product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
product
LXI Microwave Multiplexer, SP4T, 10-Bank, 67GHz, 50Ω, SMA-1.85
60-803-810
Our 60-803-810 is a 10 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
PXI Multiplexer, Single 16-Channel, 4-Pole
40-630A-022-16/4
The 40-630A-022-16/4 is a single 16-channel, 4-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Surface Potential Measuring Instrument
In the electronic equipment assembly process, there are many items that are charged on the order of kV, such as resin molded products and films. This digital electrostatic potential measuring instrument is suitable for processes with relatively high electrostatic control voltage.The measurement range switching function makes it possible to measure from low potential measurement of electronic devices to high potential measurement of resin molded products, film / printed circuit board manufacturing, etc.
-
product
50 Ohm SMB to SMB Cable Assembly
40-977-511-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 0.5m, 250 Port
A500RMR-F-5C050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Solid State Drives
Curtiss-Wright Defense Solutions
SSDs are removable mass storage devices used in data recorders. They provide rugged storage of data. The SSD is easily removable and can be connected to a PC (via a GTS/BAY/001 or similar device). The SSD uses an eSATAp connector when connected to a PC. When inserted in an some network recorders, it automatically switches to the recorder's internal connector.
-
product
Shaft Speed Pulse Generators and Shaft Speed Targets
Shaft Speed Targets are needed to generate a pulse for a Speed Sensor that is monitoring a shaft for RPM (Revolution Per Minute). Electro-Sensors Pulse Generators provide the shaft speed target needed for shaft speed detection with a sensor or switch. We have many options available for all your application needs including customizable split collar pulser wraps.
-
product
Switching Product Family
Series G2
Universal Switching Corporation
Our Series G2 product line has been introduced for a new millennium where demands for performance, quality and cost effective switching products are in high demand. Series G2 modules provide a flexible solution to most switching applications in the communications, ATE and broadcast industries. Solid-state, relay and digital products are offered in a modular form designed to be installed in one of our Series G2 mainframes.
-
product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 16 Channels
DN2.591-16
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
General Purpose Switching System
LX Series
The LX Series matrices are reliable, low cost, and versatile switching systems. A modular design concept is used. Interchangeable control modules, switch modules, and display modules can be assembled into matrices, multiplexers, or individual switch point configurations. All chassis have full front panel LED displays. Status feedback from all switches is provided.
