Filter Results By:
Products
Applications
Manufacturers
Signal Analyzers
demodulate and analyze signals.
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
- Virginia Panel Corporation
product
Signal / 20-26 GHz / 75 Ohm HD, Module, Receiver, TriPaddle, iCon Series, 64/8 Position
510160115
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161115. (May mate with other ITA modules, as well.)
-
product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
product
Compact Multiformat Signal Analyzer
CVM-306-3GB
The Videotek® CVM-306 multiformat signal analyzer boasts integrated video and audio signal monitoring in an affordable, compact package. With a robust feature set and space-saving design, the CVM-306 allows even the most modest installation to benefit from high-end monitoring and a professional look.
-
product
Saluki S5700 Series Field Comm Analyzer (SA/CA/OPTICAL)
S5700 Series Field Comm Analyzer combines the highest performance operating specifications and multi-functional measurements such as cable and antenna system analysis, fiber inspection, spectrum analysis, cellular signal demodulation, interference analysis, signal coverage mapping and RF/optical power measurements in a single instrument.
-
product
Saluki CSA Series Signal Analyzer (Modular)
Saluki CSA series signal analyzer reaches the frequency from 100 kHz to up to 26.5 GHz with a maximum of 40 MHz analysis bandwidth. It can test signal power, frequency, phase, P-1, TOI, OBW, channel power, spurious, ACPR, CCDF, SEM, EVM, and other indicators. It can be used independently or combined with the chassis to form a test system.
-
product
100MHz, 2 Channel PXI Oscilloscope, Spectrum Analyzer, Transient Recorder & Voltmeter
TE6100
The TE6100 is the first 100 MS/SEC measuring instrument that consists of a Digital Storage Oscilloscope, Spectrum Analyzer, Transient recorder and Voltmeter. This new PXI based, compact measuring instrument, can solve almost every measurement problem. Analyzing signals is done with an 8-bit resolution and a maximum sampling speed of 100 MHz. The input ranges 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
product
Mid-Range Gas Filter Correlation Carbon Monoxide Analyzer
Model T300M
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance from low to high range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Audio Analyzer
BK2110
The BaKo BK2110 Audio Analyzer is a 2 channel Digital Signal Processing (DSP) based system so you can analyze a stereo signal from an acoustic device. And because it is DSP based, it can quickly and accurately test high quality digital audio devices. All test items can be measured simultaneously and you can see them in real time or, using the LAN interface, send them to a computer system to analyze.
-
product
Logic Analyzers
Scientech Technologies Pvt. Ltd.
Logic analyzer is the electronic instrument which is widely used for testing complex digital or logic circuits. It captures and displays multiple signals from a digital system or digital circuit. Although oscilloscopes can perform many of the functions of a logic analyzer, the analyzer is more suited to operating in a digital environment because it is able to display relative timing of a large number of signals. The PC logic analyzers are a particularly cost effective method of creating an analyzer.
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-01
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
product
Spectrum Analysis
S95090B
The S95090B spectrum analyzer (SA) measurement software adds high-performance microwave spectrum analysis to PXI VNAs. With fast stepped-FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The S95090B software uses the PXI network analyzer's test and reference receivers to complete simultaneous spectrum measurements. Multi-channel SA measurements leverage the PXI VNA's internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The S95090B spectrum analyzer software application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy. Optional external attenuators should be connected with the VNA’s test ports to avoid receiver compression when measuring large signals.
-
product
PXI-2547, 2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-47
2.7 GHz, 50 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2547 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2547 makes it ideal for test systems that require the switching of a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
product
In-Situ Cross- Stack Laser Analyzer
LS25 is an in-situ analyzer for non-contact measurement of the concentration of gases. The measuring principle of the LS25 is based on the principle of single line spectroscopy (Tunable diode laser absorption spectroscopy, TDLAS). A single cross-sensitivity-free absorption line of the gas to be measured is selected in the near infrared range. A single-mode diode laser operating at room temperature scans the respective absorption line. By using an opposite receiver, the absorption caused by the sample gas is measured and from this the concentration is calculated. An automatic correction for pressure and temperature changes is possible. In addition, the transmission is displayed respectively output as a signal for preventive maintenance.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
MDA 8000HD Motor Drive Analyzers
MDA 8000HD Series
The Motor Drive Analyzer is built on an 8 channel, 12-bit resolution oscilloscope platform. It acquires any signal and performs three-phase electrical and mechanical power calculations. It provides complete power section and embedded control test coverage.
-
product
Guzik Signal Analyzer
GSA 6000 Series
Works with Read-Write Analyzer RWA 4000. Guzik Signal Analyzer (GSA) 6000 series combines high-speed waveform digitizer with built-in digital signal processing hardware and high-speed data transfer link to a computer. The Signal Analyzer comes in a space-saving display-less 2U 19” rack-mounted form factor.
-
product
Mixed Signal Scope & Waveform Generator
BS120
BS120 combines a powerful Mixed Signal Scope with an integrated DSP waveform generator and logic analyzer.
-
product
Automation
Signal Filtration
Signal Filtration is used for filtering signals coming to the input channels of spectrum analyzers, strain-gauge stations, and seismic stations, for further processing by ZETLAB programs. Signal Filtration can also be used for processing virtual channels created by such programs as Vibration Meter, Strain-Gauge Sensor, etc. Signal Filtration operates with signals both in real time and with reproduced of recorded signals.
-
product
LAN (PoE) Expansion Kit (supporting Gbit Ethernet)
OP-SB89G
OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate.
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
USB-based Digital Oscilloscope
DSCope Series
DSCope is small(115mmx74mmx16mm), and can be packed in a shirt pocket. Combined with big screen and powerful performance computer, DSCope series oscilloscope can provide you amazing signal capture and analyzer experience.
-
product
Other CATV Meters
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers. also you can find other more equipment in CATV / Broadcasting fileds, such as Three Frequency Points, HFC Return Path Signal Generator, Return Path Signal Generator, Digital RF Signal Generator and so on.
-
product
Measurement
DC Voltmeter
DC Voltmeter is used for measuring DC voltage coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the DC voltage mean value and root-mean-square deviation (RMSD) from the mean value of the selected channel signal. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module and FFT spectrum analyzer or a virtual channel.
-
product
32-CH 80 MB/s High-Speed Digital I/O Card
PCIe-7300A
ADLINK PCIe-7300A is an ultra-high-speed digital I/O card. It consists of 32 digital input/output channels. High performance designs and state-of-the-art technology make this card ideal for a wide range of applications, such as high-speed data transfer, digital pattern generation and digital pattern capture applications, and logic analyzer applications. Trigger signals are available to start the data acquisition of pattern generation.
-
product
Mid-Range Gas Filter Correlation Carbon Dioxide Analyzer
Model T360M
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Spectrum Analyzer
The Spectrum Analyzer software is designed to analyze RF signals with a frequency of up to 10 GHz in automated testing programs, to study periodic signals in the RF and microwave ranges in the frequency domain, as well as to analyze the parameters of signals with analog modulation (AM, FM, PM).
-
product
PCI EXPRESS® Protocol Solutions
PCI Express® technology is implemented broadly in systems requiringhigh-speed data transfer, such as video or graphics.Keysight's PCIe protocol solutions provide a complete PCIe 5.0 test path with a PCIe protocol analyzer and a PCIe exerciser. The integrated design boosts signal integrity and provides outstanding verstaility.Keysight's protocol solutions enable faster, more confident testing of PCIe designs, now and in the future.
-
product
PXIe Vector Network Analyzer, 10 MHz To 20 GHz
M9834A
The M9834A PXI network analyzer (VNA) offers unrivaled performance for testing multiport, multisite, multi-DUT modulated signal measurement from 10 MHz to 20 GHz.
-
product
Upstream Monitoring System
X16/KWS & VAROS 107
Fast internet services, VoIP, online gaming … an interferencefree return path is essential for a high-quality broadband DOCSIS connection. The combination of a special KWS version of the real time X16 Kronback Tracer spectrum analyser in the headend and the successful portable TV analyzer VAROS 107 as a field device provides a system that ensures high signal quality in the upstream frequency range.
