Filter Results By:
Products
Applications
Manufacturers
Pulse Amplifiers
increase amplitude while keeping waveform. AKA: Pulsed Amplifiers
- Pickering Interfaces Inc.
product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Pulse Signal Amplifier
VCH-606
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
product
DC-Coupled Pulse Amplifiers
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
product
Non-Linear Pulse Amplifiers
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
product
Astronics PXIe-1209 , 2-Channel, 100 MHz PXI Pulse Generator
785033-01
2-Channel, 100 MHz PXI Pulse Generator - The Astronics PXIe-1209 provides dual independent pulse generation with full control of all timing parameters with extremely high resolution. Both channels are fully independent, and you can configure pulse delay, double pulse spacing, pulse width, and period. Each channel offers front panel trigger inputs with software-programmable thresholds and PXI backplane triggering.
-
product
200 MS/s Waveform Generator & Dual 50 MHz Pulse/ Timing Generator
3172
The Racal Instruments™ 3172, a 200 MS/s Waveform Generator and Dual 50 MHz Pulse and Timing Generator, combines multi-instrument density and highfrequency performance in a single-slot, C-sized VXIbus format.Waveform output in the range of 100 μHz to 30 MHz with 16-bit vertical resolution (12-bit vertical for 3171 emulation) and pulse output to 50 MHz make the 3172 a powerful solution to a variety of test stimulus requirements.
-
product
Dual Channel 100 MHz Pulse Generator
PXIe-1209
The Astronics Test Systems PXIe-1209 PXI is a high-performance, 2-channel, 100 MHz Pulse Generator. Occupying a single PXI Express peripheral slot or hybrid slot, the PXIe-1209 provides dual independent pulse generation with fullcontrol of all timing parameters with extremely high resolution.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
PXI Bus Signal Amplifier
3222
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
Wideband Amplifier PXI Card
GX1222
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
Signal Amplifier
A10150
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
A10160
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9400
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9100A
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Terminal Board for Mitsubishi MR-J3-A Servo Amplifiers
DIN-814M-J3A0
This well-designed motion control terminal board is for the users who use Mitsubishi J3A servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8132.
-
product
Laser Sources and Amplifiers
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
product
30 VA Synchro Booster Amplifier
44PA1
The 44PA1 is a military grade Synchro Booster Amplifier that delivers 30 VA over the frequency range of 47 Hz to 10 kHz and will drive most CTs or TRs. It is transformer isolated, short circuit protected, and provides an accuracy of up to ±3 arc minutes.
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
Amplifier Operating with High Temperatire Accelerometers Where Pyroelectric Effects may be Encountered
Trig-Tek™ 203PC-1/2
Operates with high temperature accelerometers where pyroelectric effects may be encountered, with frequency range from 3 Hz to 40,000Hz
