Loop Simulators
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Modular Breakout System 78-Pin D-type Plugin Module
95-200-001
The 95-200-001 Plugin Breakout Module is designed to be fitted to a PXI 40-200 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 37-Pin D-type Plugin Module for 40-295
95-295-001
The 95-295-001 Plugin Breakout Module is designed to be fitted to a PXI 40-295 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 50-Pin D-type Plugin Module for 40-198
95-198-001
The 95-198-001 Plugin Breakout Module is designed to be fitted to a PXI 40-198 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module
95-191-002
The 95-191-002 Plugin Breakout Module is designed to be fitted to a PXI 40-191 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 37-Pin D-type Plugin Module for 40-293
95-293-001
The 95-293-001 Plugin Breakout Module is designed to be fitted to a PXI 40-293 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
High-speed Fiber Stretcher
PZ1
The PZ1 is the high-speed member of our family of fiber stretchers. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, variable optical delay, general purpose fiber interferometry and large angle modulation of interferometric phase.
-
product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Mid-Range Fiber Stretcher
PZ3
The PZ3 is the mid-range member of our family of fiber stretchers. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, variable optical delay, general purpose fiber interferometry and large angle modulation of interferometric phase.
-
product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
LOCAL LOOP SIMULATOR FOR TR-114 INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
-
product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
product
PXI Analog Output / Current Loop Simulators
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
sbRIO-9862, Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module
785963-01
Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The sbRIO‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The sbRIO‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The sbRIO‑9862 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
High-efficiency Fiber Stretcher
PZ2
The PZ2 provides the most extensive stretch of our stretcher product family. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, white-light scanning interferometry and large angle modulation of interferometric phase. The PZ2 is ideal for use in OCT [Optical Coherence Tomography] and OCDR [Optical Coherence Domain Reflectometry] applications requiring scattering or boundary definition measurements.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
Modular Breakout System 78-Pin D-type Plugin Module for 40-525A
95-525A-001
The 95-525A-001 Plugin Breakout Module is designed to be fitted to a PXI 40-525A Signal Insertion & Monitor Matrix Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Modular Breakout System 160-Pin Plugin Module
95-190B-003
The 95-190B-003 Plugin Breakout Module is designed to be fitted to a PXI 40-190B Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
NI-9862, CAN Interface Module
781639-01
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
product
Heat Cycling System
Yangzhou Power Electric Co., Ltd
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up.The system can perform the heat cycle testing for power cables type test and pre-qualification test according to IEC 60840, and IEC 62067 etc. Based on pre-qualification test needs, test system is divided into two parts: test sample loop and simulation temperature loop.
-
product
Modular Breakout System 37-Pin D-type Plugin Module for 40-296
95-296-001
The 95-296-001 Plugin Breakout Module is designed to be fitted to a PXI 40-296 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
