Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Load Board
cPCI 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Load Board
cPCI Serial 3U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Load Board
cPCI 6U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
Load Module for SLSC
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
product
Load Bank
Triton and Trident
The Triton and Trident Load Banks are completely self-contained, freestanding units which include all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, cooling system, control power supply, unit controller and malfunction detection system and NEMA type enclosure. These Load Banks utilize the same cabinet design.
-
product
Terminations (Loads)
Loads find wide use as accessories for both broadband and narrowband measurement instruments. Keysight's family of fixed and sliding loads includes both general purpose grade loads as well as loads intended for use as calibration standards.
-
product
Load Bank
Neptune
The Neptune Load Bank is a completely self-contained, freestanding unit which includes all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, cooling system, control power supply, unit controller and malfunction detection system and NEMA type enclosure.
-
product
Load Banks
PARELO
Amfax introduce the latest generation of load banks we affectionately call PARELO. This range of load banks provides a combination of high performance passive resistive loads along with extreme flexibility of use. This is achieved by our unique FLEXI-phase Switching(TM) technology.. Designed primarily for offering high wattage loads for the aerospace, energy, automotive and transport sectors. PARELO load banks are a cost effective solution for companies requiring high wattage loads when testing their products.
-
product
Load Cells
Force Logic UK provides high-quality load cells, load indicators, and force measurement systems for a variety of industries. All our load cells are manufactured in the UK, and have passed through rigorous quality control standards for precise and accurate measurement, load monitoring systems, and industrial weighing applications. They are suitable for the measurement of static loads and dynamic forces in tension or compression, our load cells cover a wide range of mechanical forces, from 1kg to 1000 tonnes.
-
product
Load Cells
An array of load cells, including bending beam, tension and compression link, button, low profile, through hole, S type, cannister, tension link, and single point load cells as well as load pins.
-
product
Load Cells
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
product
Load Banks
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
product
Load Bank
Titan
Very high capacity electrical loads, typically in excess of 10MW, for testing, maintenance and performance analysis of large AC power systems can be formed using the Simplex Titan Load Bank as a building block element. The Titan Load Bank is a self-contained, semi-portable unit providing resistive and inductive loads to 15KVA, .8 power factor, to 600VAC.
-
product
Load Banks
EL Series
*12kW, 15kW and 18kW DC Electronic Load*All of our Load Banks are continuously rated for Power and Current.
-
product
Load Logger
LL-230
AMETEK LoadLoggers* and LoadProfilers are non-invasive digital recording loggers for gathering data on distribution loads and power quality. Whether the data is from a load site or direct from the distribution system, the AMETEK Load Management products are easy to install, operate and analyze.
-
product
Load Banks
BD Series
*12 kW, 15kW and 18kW Battery Discharge Load DC*All of our Load Banks are continuously rated for Power and Current.
-
product
Load Cells
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
-
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
-
-
product
Load Pins
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
Load Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
-
product
Load Boards
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
product
Load Cells
Load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or balance and transmit it to a weight indicator . The load cell is an essential component in any scale or electronic balance and they come in different models and specifications. A Wim load cell is essential for a weighing system where precision, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for each need, in addition to offering all the advice you need to choose the model that best meets the particular needs of your weighing system and always backed by WIM-Systems quality and technology.
-
product
Electronic Loads
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
product
Load Bank
RLB
RARA manufactures load banks, ranging from small portable units for testing generators to multi-megawatt designs for larger applications. Regular load testing, along with correct battery maintenance, is the best way of ensuring the reliability of standby power systems. It is routine for all newly-installed generating sets to have a load test during the commissioning process in order to prove the performance of the set and all ancillaries-cooling system, exhaust system, switchgear and protection schemes.
