Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Mini Pneumatic, Contact, Receiver, Push-in Fitting, for 4 mm OD Tubing
610131111
Primary mating contact 610132111.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
product
HEAD artificial head microphones
HSU III
The HEAD-Shoulder-Unit HSU III is an artificial head microphone for binaural recordings.
-
-
product
Head Expanders
By increasing the mounting area of the shaker, multiple items can be tested at the same time, decreasing total test cycle time. In addition, with Guided Head Expanders, payloads with large foot prints can be safely mounted and tested on the shaker, minimizing the risk of damage to the shaker suspension system. Although many head expanders are resonant below 1000 Hz, average or extremal control allows operation to 2000 Hz.
-
product
Laser Heads
The laser head is the source of the laser beam used in all laser motion and position measurement systems. The primary difference between laser heads is in the velocity, reference frequency and optical output power. Other considerations are size, heat dissipation, and input power requirements. Which laser you choose depends primarily on the application in which it will be used. For example, semiconductor lithography systems typically have faster moving parts (stages), and therefore need higher velocities than machine tool applications.
-
product
Wrench Heads
Mountz offers a range of imperial and metric wrench end fittings for various the Mountz wrench handles. Open ends, box head ends, flare ends, ratchets and blank ends can be supplied in metric or imperial to suit almost every application. Other sizes may be available. For sizes not displayed please contact Mountz Inc.
-
-
product
Compression Head
G201A31
To simulate the subjecting of a child-related product to mechanical damage through compressing or other action likely to be performed by a child. After testing, the product may be tested for sharp edges, sharp points & small parts.
-
product
Laser Head
5517C
The Keysight 5517C is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Option 009 allows a larger angular range of measurement by providing a 9 mm beam diameter for use with three-axis interferometers. Please contact Keysight for custom requirements.
-
product
Laser Head
5517A
The Keysight 5517A is used primarily in VME and PC based laser interferometer systems where the velocity of motion is slower, such as machine tool applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517FL
The Keysight 5517FL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517CL
The Keysight 5517CL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Option 009 allows a larger angular range of measurement by providing a 9 mm beam diameter for use with three-axis interferometers. Please contact Keysight for custom requirements.
-
product
Laser Head
5517B
The Keysight 5517B is used primarily in VME and PC based laser interferometer systems where the velocity of motion is slower, such as machine tool applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517EL
The Keysight 5517EL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517GL
The Keysight 5517GL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517DL
The Keysight 5517DL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Laser Head
5517D
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Hydrostatic Head Tester
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
product
Optical Head Interface
N7749C
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
product
Thermocouples With Terminal Heads
Thermocouples with Terminal Heads including Mineral Insulated, Industrial Style & remote wall mounted housing thermocouples.
-
product
Probes With Industrial Heads
Used in industrial applications for process temperature measurement, these probes come in a variety of protection head styles for easy connection wiring to your extension cable
-
product
Protection Heads And Tubes
Choose from a wide variety of industrial protection heads and tubes to protect your temperature sensor probe from your rugged process application or surrounding environmental conditions.
-
product
Square Head Fiber
Panasonic Industrial Devices Sales Company of America
Panasonic Square Head Type Fibers are compact and allow for right angle, space-saving installation, with minimum pitch using needle-nose pliers. These Fibers are also lens compatible for longer detection.
-
product
Laser Scan Heads
Aerotech supplies high-performance 2D, 3D and 5D laser scan heads to meet a diverse range of precision manufacturing challenges. Choose from standard options or leverage our expertise in designing laser manufacturing systems.
-
product
WLCSP Probe Heads
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
product
Hydrostatic Head Tester
TF163
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester, used for determining the resistance of fabrics (canvas, coated fabrics, cover cloth, rainproof clothing fabrics, and geotextile materials) and films to water penetration under pressure while firmly clamped in the test rig of standard area.
-
product
Renishaw Probe Heads
Advanced Industrial Measurement Systems
Conventional touch-trigger measurement methods rely on speeding up the motion of the CMM’s 3 axes to measure quickly – PH20 utilizes the head motion technology developed for the multi-award winning REVO system to minimize the dynamic errors of the CMM at higher measurement speeds
-
product
Universal Scanning Head
CF106
Calmet Smart Calibration Devices
Universal miniature scanning head for detecting (counting) impulses from inductive, LED and LCD energy meters. Additionally it enables counting of manually triggered impulses (Start/Stop push button function). Sometimes (when access is difficult) it is the only way to count pulses from inductive, LED and LCD meters.
-
product
Hydrostatic Head Tester
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester, used for determining the resistance of fabrics (canvas, coated fabrics, cover cloth, rainproof clothing fabrics and geotextile materials) and films to water penetration under pressure while firmly clamped in the test rig of standard area, by means of dynamic test method and static test method.
-
product
Test Head Manipulators
Cobal 250
The Cobal 250 offers the best-in-class range of motion for universal manipulators with seven degrees of motion. Separate linear movements make it easier for the operator to dock, undock, and redock the test head in seconds. In combination with inTEST EMS docking, the Cobal 250 is compatible with testers for both Wafer Sort and Final Test, minimizing the time and cost when moving a tester between Sort and Final Test.
-
product
Remote Radio Head
CMPHEAD
The separate one-box tester and the R&S®CMPHEAD30 RRH concept allow short RF cable lengths for an optimal link budget in radiated test environments. This approach enables testing of fully assembled FR2 devices and RFICs with both IF and mmWave RF interfaces. The multi-band R&S®CMPHEAD30 covers all important FR2 bands
