Filter Results By:

Products

Applications

Manufacturers

Generators

Generation of electrical, mechanical, data, electrical, vapor or gas states.

See Also: Waveform Generators, Frequency Generators, RF Generators


Showing recent results 751 - 763 of 763 products found.

  • Motor Winding Ohmmeter

    RMO-M Series - IBEKO Power AB

    The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement

  • OTR Systems

    OTR 1001 - OmniTek

    The Omnitek OTR systems offer a combined data analyzer and test signal generator in a rackmount format. The OTR 1001 system is provided in a 1RU format; the OTR 1003 is provided in a 3RU format. As data analyzers, the OTR systems offer full resolution picture monitoring; comprehensive SDI input status information; waveform, vectorscope and gamut displays; and SDI physical layer analysis including eye-pattern and jitter displays. As signal generators, they provide a full range of standard test patterns and zone plates; uncompressed video capture and play-out; gain, noise, bounce and jitter insertion; audio tones, timecode, WSS, video index and SMPTE 352 generation. The facilities offered have recently been enhanced through the addition of a Stereo 3D monitoring option, providing a comprehensive range of colorimetry and depth-analysis functions.

  • TRF Manager 9

    Epsillon s.r.o.

    Configuration by using a PC, this is one of the major TRF generator attribute. Instruments have factory settings suitable for common applications and contain the most popular test patterns. But many users want to customize the setup or set the instrument according to specificic application requirements. They also may want to adjust parameters, that cannot be accessed by any other way. That is what TRF Manager 9 (optional software pack) can do. And much more! Pattern generators of the TRF-498 and 598 series use a parallel interface for connection with PC. Basic setup can be realized by using Pattern Manager, free software downloadable from our site. For advanced settings there is available TRF Manager 3 software. For more detailed information see the TRF-498 and TRF-598 section, please.

  • RF Signal Generator With 1.5 And 3GHz Models

    TGR205x Series - Aim-TTi

    150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators

  • UPS System JOVYSTAR PLUS 3: 1

    JOVYATLAS

    The UPS systems of the JOVYSTAR PLUS series have a PFC rectifier in IGBT technology (Insulated Gate Bisolar Transistor) with a very large input voltage range and a power factor cos φ of almost 1. All systems of this type are equipped with a self-diagnosis system and have a high dynamics with load jumps as well as an extremely low noise level. The harmonic content (THDI) of the rectifier is below 4% in nominal operation. This low THDI enables a smaller dimensioning of emergency power generators than with conventional rectifiers in thyristor technology. All system data can be called up on an RS232 interface and can be transferred via an SNMP adapter, a MODBUS adapter or via a PROFIBUS in a LAN or other bus system. The battery is integrated in the UPS housing. The single-phase UPS systems of the type JOVYSTAR PLUS are available in the output sizes 10, 15 and 20 kVA.

  • Test Engines

    Verified Systems International GMBH

    The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.

  • Programmable Digital Attenuator

    LDA-602EH - Vaunix Technology Corporation

    The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.

  • Universal Programmer Superpro 610p

    Xeltek

    Until now,Support 243 IC manufacturer, 33941 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V.Extremely fast speed hign than SUPERPRO/500P.Built with 48 universal pin-drivers.PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip.Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking.Over-current and over-voltage protection for safety of the chip and programmer hardware.WINDOWS XP/Vista compatibility/Win7/Win10

  • AC Fuel Flow Signal Generator

    TA-100 - Tech-Aid Products

    The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.

  • Frequency Converter Upwards

    UPCONVERTER 10 GHz LXI - Holding Informtest

    UPCONVERTER 10 GHz осуществляет программно управляемый перенос вверх спектра шириной 150 МГц, поступающего на вход сигнала, в любую точку спектрального диапазона от 10 МГц до 10 ГГц. Перенос спектра осуществляется по супергетеродинному принципу с тремя ступенями переноса. Благодаря этому во всем рабочем диапазоне спектра достигаются высокие уровни подавления несущей частоты и зеркального канала. Также UPCONVERTER 10 GHz обладает уникальной возможностью, не имеющей аналогов среди приборов подобного типа – задавать значение промежуточной частоты (входного сигнала) для переноса в диапазоне от 50 до 400 МГц. Помимо этого, прибор позволяет передавать входной сигнал частотой от 0,1 до 400 МГц напрямую на выход, без переноса. Благодаря этому, совместно с UPCONVERTER 10 GHz в качестве генератора промежуточной частоты может быть использован широкий спектр генераторов зарубежного и отечественного производства. Холдинг «Информтест» предлагает потребителям генераторы собственной разработки MGKS and MGVCh , as well as the first Russian MT transceiver module , which are fully compatible with the input characteristics of UPCONVERTER 10 GHz. Together with generators produced by the holding "Informtest" UPCONVERTER 10 GHz under the control of a common software shell makes up a synthetic instrument - a ready-made solution for testing microwave devices and radio reception channels.

  • Single-Phase Transformer Winding Resistance Meters

    RMO-TD Series - IBEKO Power AB

    Using the most advanced switch-mode technology available today, the RMO-TD series is ideal for winding resistance measurements of inductive objects. Transformer resistance meters and tap changer analyzers are perfect for testing:transformer windings (power transformers, distribution, autotransformers),all types of tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.In addition, transformer demagnetization can also be done with all RMO-TD instruments.The RMO-TD series contains 3 models, with maximal test currents from 25 A (RMO25TD) to 60 A (RMO60TD).The three independent voltage sense channels enable testing of three windings in series. This enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.All RMO-TD transformer resistance meters have a built-in tap changer control unit. It enables remote control of on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, DV-Win software is included which can be programmed to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.

  • Universal Programmer Superpro 7500

    Xeltek

    Until now,Support 396 IC manufacturer, 94596 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V. The programming speed up further increase 30% compared to SUPERPRO 5000.The programmer support files up to 256 GBytesBuilt with 144 universal pin-drivers.Universal adaptors are available for varies packages up to 144 pins. New device support will be easier. PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via the 6-KEY keypad and the 20 character by 4 line LCD display. A SD card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility

  • Single-Phase Transformer Winding Resistance Meters

    RMO-TT Series - IBEKO Power AB

    RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.

Get Help