-
product
Global Positioning System Sensors
GPS
GPS sensors are receivers with antennas that use a satellite-based navigation system with a network of 24 satellites in orbit around the earth to provide position, velocity, and timing information.
-
product
GPS, GLONASS, Galileo Splitter 2 Way, N Type, 1000 - 2000 MHz, 50 Ohm, Passive
GPS200
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy N Type Female (Jack) 50 Ohm
-
product
GPS Signal Splitter 12 Way, N Type Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS120
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy Type N Female (Jack) Low PIM
-
product
Digital Relay and Merging Unit Tester
POM2-3333
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
product
1231a Very High Frequency Distribution
Precise Time and Frequency, Inc.
The ptf 1230A(1U)/1231A(2U) GPS L-Band RF Distribution amplifiers provide high performance GPS signal references for laboratory or systems use. In most applications the low noise and signal gain capability of the units will provide userswith a robust GPS signal source for lab or system requirements.The ptf 1230A/1231A uses individually buffered output stages and insures maximum isolation between the individual outputs. The ptf 1231A offers 12 outputs. Options are available for a 2U/3.5” version (ptf 1230A) with 24 outputs.Isolation from output to output is >-40 dB. The input also offers DCV for biasing an active antenna.
-
product
GPS Antenna Signal Splitter 6 Way, N Type, Passive, L1 & L2, 50 Ohm
GPS600
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
product
Radio Link Simulator
RLS-2100
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
product
Omnidirectional Antennas
In radio communication, an omnidirectional antenna is a class of antenna which radiates equal radio power in all directions perpendicular to an axis (azimuthal directions), with power varying with angle to the axis (elevation angle), declining to zero on the axis.[1][2] When graphed in three dimensions (see graph) this radiation pattern is often described as doughnut-shaped. Note that this is different from an isotropic antenna, which radiates equal power in all directions, having a spherical radiation pattern. Omnidirectional antennas oriented vertically are widely used for nondirectional antennas on the surface of the Earth because they radiate equally in all horizontal directions, while the power radiated drops off with elevation angle so little radio energy is aimed into the sky or down toward the earth and wasted. Omnidirectional antennas are widely used for radio broadcasting antennas, and in mobile devices that use radio such as cell phones, FM radios, walkie-talkies, wireless computer networks, cordless phones, GPS, as well as for base stations that communicate with mobile radios, such as police and taxi dispatchers and aircraft communications.
-
product
GPS And GNSS Simulators
Safran’s GPSGlobal Positioning System is a navigation satellite system. See also / GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also satellite simulators are easy to use, scenario-based instruments that combine a powerful, feature-rich platform with industry-leading value and affordability for any requirement for GPS testing.
-
-
product
Seismograph
DX6
The DX6 is a 6 channel seismograph that can be used for almost any seismic project. With its internal memory, optional USB memory and GPS, the flexible DX6 node can be deployed anywhere, at any time.
-
product
Marine Logging System
SuperSting Marine
The SuperSting Marine continuously records and stores data from a GPS receiver. Current is injected every 3 seconds and 8 apparent resistivity values representing 8 depth levels are read for each current injection. Depth of penetration depends on length of the cable and array type. Typically you will see down to aproximately 20% of the electrode spread length.
-
product
SparkFun GPS-RTK Board
NEO-M8P-2 (Qwiic)
With GPS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GPS Real Time Kinematics (RTK) has mastered dialing in the accuracy on their GPS modules to 25mm, and that's why we had to put it on this board!
-
product
Man-Portable Aircraft Survivability Trainer
MAST™
The Man-Portable Aircraft Survivability Trainer (MAST™) is a long-range ultraviolet (UV) stimulator capable of testing aircraft electro-optical (EO) sensor suites up to 5 km (3.1 mi). Designed to operate as a pilot training tool, MAST comes equipped with day/night video recording and precision GPS instrumentation for after-action review of simulated engagements.
-
product
1pps-Locking-Modules
This is a module to control an OCXO or Rubidium oscillator with 1PPS from a GPS receiver. The Quartzlock A6-1PPS uses a 3 state Kalman filter algorithm to measure & correct the frequency offset of the oscillator with respect to the 1PPS input. Time-tagged input 1PPS to 200ps resolution & <1ns jitter. Analog interpolator is self calibrating. Interface to GPS decodes messages & extracts relevant info. i.e. time correction data for 1PPS output, this has AVAR of the Rb or OCXO i.e. 5 x 10-12/s & <100ps RMS jitter. The output is steered to time coincidence with GPS time/UTC to 1ns resolution. Holdover initiated by 1PPS fail or data from GPS RX that 1PPS is inaccurate. During holdover, measured frequency offset & drift steer the oscillator & 1PPS is still available.
-
product
Weight Drop Controller
WDC
The WDC unit consists of the following: *Weight Drop Relay Control System *Radio Trigger Module (RTM) *Remote Control Box *Radio*Hammer Switch The WDC provides following features: *Automatic cycling with user entered number of hits*Time Delay Display (Time from fire command to hit)*GPS interface for position and timing*Remote Control Box
-
product
Radio Trigger Module
RTM3
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
product
Single Rear Slot Universal Low-Profile PCI to Compact Flash Adapter
P312
To cater for the latest generation of Low Profile PCs that can only use Low Profile PCI add-in boards, Elan has created the P312. This model, from the P-Series range, features a Compact Flash Type II ejector and a circuit board that conforms to the MD1 profile specification. It will allow you to use any Compact Flash card such as IBM MicroDrives, Bluetooth cards, WLAN 802.11b cards, data acquisition cards, pager cards, GPS cards etc.
-
product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 2 Ports
GPS212
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
product
SparkFun GPS Dead Reckoning Breakout
NEO-M8U (Qwiic)
The SparkFun NEO-M8U GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M8U takes advantage of u-blox's Untethered Dead Reckoning (UDR) technology. The module provides continuous navigation without needing to make any electrical connection to a vehicle, thus reducing cost of installation for after-market dead reckoning applications.
-
product
2 Way GPS / GNSS Signal Splitter IP67 Outdoor, SMA, 1-2 GHz, 50 Ohm, Passive
GPS211
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
product
Modernized Navstar Security Algorithm (MNSA) M-code Testing
SimMNSA
The M-code signal is part of the security architecture that all new Military GPS User Equipment (MGUE) has been required to use since 2017. Until recently, testing with non-classified AES-encryption and replay of M-code Satellite Data Sets (SDS) have been the only methods authorized for GPS M-code receiver testing using a constellation simulator.
-
product
Precision Marine Geodetic Systems
Using leading-edge "Broadband Acoustic Spread Spectrum Technology", accurate sound wave traveling time between LinkQuest's subsea precision transponders and surface station can be measured. When the system is integrated with a Kinematic GPS, motion sensors and a gyro on the surface vessel or undersea vehicle, sub-centimeter acoustic positioning can be achieved.
-
product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SFF
Model 6353
- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
product
AXIe High-Performance 5-Slot Chassis
M9506A
5-slot AXIe chassis with embedded system module, Gen 3 performance, 300W per slot, and GPS option.
-
product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782110-01
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module—The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
product
Qseven Rev 2.1 Application Board With LVDS, HDMI, Dual LAN And Audio
Q7B301
The Q7B301 is an ultra-compact Qseven reference carrier board which measures only 100 x 72 mm - the size is slightly bigger than a credit card. The Q7B301 is perfect for small box applications such as those found in the latest digital signs, kiosks and traffic control system. This Qseven application board offers various I/O connectors and flexible expansion features to reduce the design effort to the minimum. The Q7B301 also has an extended industrial grade operating temperature range of -40ºC to +85ºC to withstand the rigors of harsh environments. Axiomtek’s new Qseven Rev. 2.1 application board, Q7B301, is compatible with Qseven module – Q7M311 which is powered by the Intel® Pentium® Processor N4200 and Celeron® Processor N3350. Customers can emulate required functions on Q7M301 as a reference design board or integrate the Q7M301 directly into their product as the application board. Its minimum footprint also enables the maximum potential. The Q7M301 is especially suited for industrial IoT applications such as industrial control, medical imaging, digital signage, gaming machines, military, and networking. The Q7B301 comes with two PCI Express Mini Card slots and one SIM card slot for wireless communication (3G/4G, GPS, Wi-Fi and Bluetooth). For enhanced or high-definition audiovisual devices, the Qseven reference carrier board supports one HDMI and LVDS interfaces as well as HD audio and 4-channel digital I/O. More I/O interfaces include two Gigabit LANs with Intel® i211AT Ethernet controller, two RS-232/422/485, one USB 2.0, two USB 3.0, one SMBus, and one I2C. Furthermore, it has one SATA-600 interface for storage requirements.
-
product
GPS Jamming and Spoofing Detection Sensor
BroadSense
BroadSense is a GPS jamming and spoofing detection sensor designed to provide real-time and historical situational awareness data. Utilizing sophisticated GNSS receivers and patented jamming and spoofing detection algorithms, BroadSense can detect when the GPS signal or GPS spectrum is compromised.
-
product
Talon 8 Channel 6 GHz RF Rugged Rackmount Recorder
Talon RTR 2628
- Eight-channel phase-coherent RF recording- Ideal for signal intelligence, phased-array radars, beamforming, and DF (Direction Finding) systems- Records RF frequencies from 30 MHz to 6 GHz- Captures 80 MHz of instantaneous bandwidth- Eight-channel RF tuner can be set for phase-coherent operation or independent tuning- Eight 250 MHz 16-bit A/Ds- Eight DDCs with decimations to 65,536 for selectable bandwidths- 3.2 GB/sec real-time aggregate recording rate- 4U 19-inch rugged rackmount PC server chassis- Windows® workstation with high performance Intel™ processor- Front panel removable SSD drives- Up to 122 terabytes of storage to NTFS RAID disk array- SystemFlow® GUI with signal viewer analysis tool- Optional GPS time and position stamping
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
