-
product
HMM+™ Tester
Model 4702
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
product
Data Acquisition Devices
Our data acquisition and encoding systems provide significant performance in reception, signal conditioning and encoding of all types of signals while used in missiles, airborne vehicles, mobile ground-based testing and other platforms that require ease of operation, flexibility, ruggedization and small packaging.
-
product
Internet-Wide, Real-Time Data Sharing via the Cloud and the Network's Edge
Vortex Link
Vortex Link provides universally accessible Routing and Discovery Services that enable ubiquitous and transparent data sharing and WAN connectivity for Vortex DDS systems or any other system/device that uses a compliant Data Distribution Service (DDS) software stack. Vortex Link provides transparent discovery and routing between data readers and data writers regardless of location. Vortex Link supports a number of different deployment and connectivity scenarios, including individual device to cloud, system to cloud and also connecting your different LAN’s to turn them into a single system.
-
product
PXI 2A Multiplexer, 2-Bank, 32-Channel 2-Pole
40-614-011
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Web Based DIsplay Solution for Environmental Data
GeoView
Aanderaa GeoView is a web based display solution for environmental data display.Aanderaa GeoView is part of the Aanderaa Real-Time Solution. This gives the user vast opportunities for interfacing meteorological, oceanographpic, or other environmental research equipment in a networked solution giving access to data real-time.
-
product
Light Intensity Sensor
ENVIROMUX-LIS
Detects and measures the luminous intensity of light. Ideal for monitoring unmanned closets, telecom rooms, remote data rooms, or other low traffic facilities. Applications from 0 to 128,000 lux. Human eye response (540 nm peak sensitivity). IR and UV rejection. RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS. Compatible with ENVIROMUX-2D/5D/16D.
-
product
VDV & USB Cable Tester
PK-2016/2016R
The VDV & USB cable tester is designed for testing today’s media computer networks which combination of telephone USOC (voice), twisted pair (data) and coax security / alarm (video) as well as PC-USB 2.0 3.0 cables.
-
product
High Performance Data Acquisition
CPCI-AD8
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Leakage Current Clamp Tester
M-1141
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency(fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
USP 1062 Testing
What’s your compaction problem? Machine, man or materials? Answer your compaction issues and get the USP <1062> data you need to ensure you’re fully compliant with key Critical Quality Attributes for manufactured tablets.
-
product
Lens Measurement Spectrophotometers
LINZA 150
LINZA 150 spectrophotometer is designed for broadband transmittance and reflectance measurement of lenses and lens assemblies (objectives) ensuring that only perfect lenses are approved for lens assemblies, delivered to customers or meet specs provided to your lens supplier. The instrument is perfectly suited for both routine lens measurements and sophisticated improvement of lens production technology: Fast on-axis transmittance measurement of individual convex/concave lenses. Fast on-axis transmittance measurement of lens assemblies (objectives). Unattended on-axis and off-axis reflectance measurement of individual lenses providing measurement data virtually from any area on lens surface (both convex and concave). Ideal for fine-tuning of deposition technology used to produce coatings on lenses.
-
product
Terminal Housing MID JTRS & MIDS LVT
TCG
Curtiss-Wright Defense Solutions
Provide a tactical edge to warfighters with a mobile, compact, and affordable terminal housing case equipped with the technology to meet Link 16 communication requirements and supply your program with a complete tactical data link solution.
-
product
PXIe-8862, 2.6 GHz 8-Core PXI Controller
788817-0118
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
product
Interfacing Components
Spring contacts and lands for PCB interconnection and a wide range of data, power and battery charging applications including: charging batteries in portable instruments power and data transfer pins in a docking station integral compliant contacts, such as for an antenna contact in a mobile phone board to board spring contacts for use in computerised gaming systems and telecommunications units
-
product
UHF Transceivers
Is designed to provide a wireless RF link between two orbiting spacecraft or other crafts such as a Lander on the surface of Mars, and an Orbiter craft orbiting above. The purpose of these transceivers is to facilitate the passing of data and commands between the two craft.
-
product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790660-0118
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - PCIe
Model 78721
Model 78721 is a member of the Onyx® family of high performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkeysolution.
-
product
Portable Single Yarn Strength Tester
TY420
TESTEX Testing Equipment Systems Ltd.
Portable Single Yarn Strength Tester. Used to test the breaking strength of yarn on the scene or in the lab. The instrument is controlled by micro computer. It can process the data automatically and send them to the printer. It is necessary & essential to estimate the technical index of the yarn.
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
Model Based Testing
RTT-MBT
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
product
BCI Tester
Test scenario creation function of BCI test.・Test scenario auto-run feature.・Test results file generated automatically. (CSV file: can be customized)・CAN / LIN communication function, data logging. (FlexRey available)・Power I/O, ECU I/O control functions, data logging.・Anomaly detection function display.・Noise detection function.
-
product
PXI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
40-635A-006
The 40-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
product
PXIe-7966, Virtex-5 SX95T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO
781805-01
Virtex-5 SX95T FPGA, 512 MB DRAM PXI FPGA Module for FlexRIO—The PXIe‑7966 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXIe‑7966 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software. The PXIe‑7966 supports peer‑to‑peer streaming, which directly transfers data among multiple FPGA modules or select PXI Express modules without sending data to the host processor. With this feature, you can add FPGA capabilities to high-performance NI digitizers with NIST‑traceable calibration or expand your FPGA algorithms across multiple FPGAs for computationally demanding applications.
-
product
Single Channel Oscilloscope 20M-100MHZ
HDS
Shenzhen Chuangxin Instruments Co., Ltd.
- Auto-scale function- 20 automatic measurements- Bandwidth : 20MHz - 100MHz- USB data transmission supported- Waveform record and replay- Multimeter newly supported SCPI- Rechargeable Li-ion battery (6 hours' backup)
-
product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
Instrumentation System
Reach Technologies has leveraged the success of its automotive instrumentation, and applied it to other industries. The availability of established CAN products, coupled with its robustness, makes CAN a cost effective instrumentation solution. The software back-end of our instrumentation system is comprised of a server to interface to the data loggers, a database server to manage the data, and a web server for control and data visualization.
-
product
Call Generator (Voice / Data)
Qosmotec Software Solutions GmbH
The Mobile Network Tester LTS is an automatic call generator, that establishes voice and data calls to and from actual mobile devices in the test system. Voice calls can be generated via the wireless PLMN network using actual mobile devices, via the PSTN network through analogue or ISDN lines or via Voice over IP. Wireless data sessions can be setup through the 3G or 4G network or over WiFi.
