Filter Results By:

Products

Applications

Manufacturers

Control

Known value


Showing recent results 5161 - 5175 of 6817 products found.

  • PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm

    50-296A-121-9/8 - Pickering Interfaces Ltd.

    The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • PCI Module

    PCI-6713B-4IP - ALPHI Technology

    The PCI-6713B-4IP moduleprovides a high performanceflexible I/O scheme, thatsupports industry standardIndustry Packs™. Forapplication requiring low cost,high density I/O or uniquecombinations, the 6713B-4IPis the ideal solution. The local6713B DSP can be used tosimply move data to and fromthe PCI bus or provide preprocessing functions such aslocal PID controls, FFT’s,digital filtering, etc. Customapplication software can bedownloaded to the DSP viathe PCI bus. A very low cost,non-intelligent version is alsoavailable, PCI-SIP.

  • PDL Emulator

    PDLE-101 - General Photonics Corp.

    The PDLE-101 is specially designed for such PDL-related tests. This PDL source/ emulator can generate individual PDL values between 0 dB and 20 dB, with a resolution of 0.1 dB for PDL tolerance testing. It can also generate variable PDL with user defined range, waveform, and speed for PDL tracking speed and recovery time tests. The instrument can be controlled via the front panel keypad or by remote control via USB, RS-232, GPIB, or Ethernet interfaces. The residual PMD of the unit is less than 0.1 ps.

  • Pen type Conductivity Meters

    Bestone Industrial Ltd.

    Pen conductivity meter is a precision instrument for test solution US value. Simultaneously display the U.S. value and temperature. CT-3031 Pen conductivity meter is a precision instrument used in the test solution mS value. MS value and the temperature is displayed at the same time. Its stable performance, full-featured, easy to operate and so on. Making it the field and laboratory testing and control of enterprises and institutions uS value. Widely used in the monitoring of the chemical, pharmaceutical, electronics, food and other industries

  • Phase Sequence Meters

    Beha-Amprobe

    Phase sequence meter is used for detecting the sequence of the supply in three-phase electric circuits. Since the direction of rotation of three phase electric motors can be changed by changing the phase sequence of supply. And also the correct operation of measuring instruments like 3 phase energy meter and automatic control of devices also depend on the phase sequence. Different types of phase sequence testers are available in today’s market like contact or non contact, static or rotating, etc., in a wide range of voltage or power ratings.

  • Photometric Radiometric Transmitters

    HD2021T6 / HD2021T7 - Delta OHM S.r.L.

    The transmitters allow converting the photometric quantity “equivalent veiling luminance” – HD2021T7 – or a photometric quantity Luminance (cd/m2) – HD2021T6 – into a current (4…20 mA) or a voltage (0…10 V) signal according to the version chosen. If the acquisition station is far from the probe (>50m), it is necessary to use the current output version.The probe is used for the control of street lighting, in particular, the measurement of equivalent veiling luminance is essential to determine the threshold luminance at the entrance of the tunnels (UNI 11095:2011).

  • Portable AC/DC Power Supply

    UPS S3 - Manta Test Systems

    The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.

  • Power Amplifiers

    MPA400 Series - ETS Solutions

    The ETS Solutions MPA series amplifier family is a wide frequency band digital switching (Class D) Power Amplifier designed with latest state-of-the-art technology. A number of built-in features in the amplifier allow vibration testing to be performed with ease. User friendly operation and an interactive microprocessor logic control system ensures the MPA amplifier delivers full performance and is compatible with any make of electro-dynamic shaker. The MPA400 series amplifier is matched to the mk1 and mk2, M series shaker.

  • Primary Injection Tester

    PI-4000B - ETI Precision

    The PI-4000B is a versatile and technologically advanced primary injection test set capable of testing circuit breakers up to 4000 amperes frame size. It incorporates an output transformer with dual primaries to facilitate its use on power sources of 480 VAC as well as 240 and 208 VAC, and dual secondaries to provide optimal impedance matching to a wide range of breaker sizes. An internal voltage sensor automatically configures the AC control power section to be energized only when properly configured for the applied voltage.

  • Process Controllers

    Orbit Controls AG

    Orbit Controls process controllers are designed for direct connection to virtually all industrial sensors and signal sources. They can be used as process monitors to display the process variables to be measured or as process controllers to monitor processes. In addition to the digital display, the devices also have data interfaces, analog outputs and set point outputs. Simple process monitors are optimized in the factory for the desired measuring range and function at the customer's request. The programmable controllers can be parameterized on site via the keyboard or the data interface.

  • Professional Cordless Circuit Tester

    CT8002 - General Technologies Corp.

    No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.

  • Programmable Benchtop DC Power Supply

    62000L - Chroma Systems Solutions, Inc.

    Voltage range: 0 ~ 60VCurrent range: 0 ~ 7APower range: 0 ~ 150WWide range of voltage & current combinations in constant powerLow noise: < 3mVp-pFast transient response time: < 50usHigh-speed programmingPrecision V&I measurementsStandard GPIB/USB interfaceRemote sense (Model 62010L-36-7 only)Master-slave parallel and serial control (Model 62010L-36-7 only)8 steps for auto sequencing programming16 storage locations for user-defined operating statesOVP, Current limit, Thermal protectionCE Certified

  • Programmable RF Attenuators

    Adaura Technologies

    The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.

  • Property Inspection Solution

    DJI / IMGING - Loveland Innovations, LLC.

    Advanced DJI drone solutions for the P&C Insurance industry. IMGING™ to conduct full roof and property inspections with incredible detail in as little as ten minutes from start to finish, and they’re getting high-resolution, actionable data they can use to make informed decisions. By combining Insurance-focused workflows and patents-pending autonomous flight control technology, IMGING is making roof inspections safer, quicker, and more consistent. It’s deceptively simple, amazingly powerful, and built specifically for Insurance.

  • Push Pull Testers

    IMADA, Incorporated

    Lever-operated manual systems enable rapid push/pull testing up to 220 lbf.Wheel-operated manual systems enable slower, more precise movement with the hand wheel up to 750 lbf.Motorized push/pull testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement up to 1100 lbf.All push/pull testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.

Get Help