Filter Results By:

Products

Applications

Manufacturers

Control

Known value


Showing product results. 4816 - 4830 of 6879 products found.

  • PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device

    PCIe-7858 / 786457-01 - NI

    PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can … customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7858 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.

  • PCIe, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device

    PCIe-7857 / 786458-01 - NI

    PCIe, Kintex-7 160T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7857 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can … customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7857 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.

  • 6000 Series Analog I/O Modules

    Pacific Instruments, Inc.

    Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.

  • Cupping Tester

    PCE-CPT 20 - PCE Instruments

    PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.

  • Data Acquisition Module with I/O

    SY019 - Synectic Electronics

    SY019 Data acquisition module I/O unit is fitted with a choice of either or both of 8; 4-20mA analogue inputs, 8 switch inputs, and 8 relay outputs. With 1024K bytes of onboard data logging option readings can be transferred to the logger each time a trigger is applied to the analogue inputs. The SY019 Data acquisition module is supplied with either RS232 or RS485 communications interface, with the advantage of unique address setting several units can be connected to the same port. The address to the unit are set by the on board switches. The unit is supplied in a DIN rail mounting case with an optional cover and is powered from a nominal 24Vdc supply. When used in addition to our batch controllers this unit can add extra function to expand a process control system, used standalone it can be a data acquisition system. Control engineers can write your own protocols using the command set supplied or talk to our design engineers, they can write the protocols for you. An Application for a mobile rig is still touring the world in 2019 after 11 years for Shell Global, proving the technical superiority of V Power fuel.

  • High Voltage 50 Ω Pulse Generator

    TLP-8010A - High Power Pulse Instruments GmbH

    *Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components

  • High Voltage Isolator for Logic Analyzers

    LX-08 - Link Instruments

    The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.

  • High Voltage Switching Systems

    HXV Series - Cytec Corp.

    HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.

  • Power Quality Analyzer

    PQM-703 - Sonel S.A.

    Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.

  • SWR True Antenna Analyzer

    COMM-connect

    SWR True Antenna Analyzer is a versatile analyzer covering all major communication bands from 30MHz to 2700MHz. The SWR True will analyze antennas and cables. Measurements are represented graphically as VSWR or Return Loss plots. The built in PLL synthesized generator offers a superior accuracy with small step size. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The SWR True instrument is small, handy and light weight battery operated with more than 6 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.

  • 16-Bit, 1 MS/s, 16-Channel Signal Generator Adapter Module for FlexRIO

    NI-5741 / 782864-01 - NI

    The NI‑5741 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5741 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5741, you must pair it with a compatible PXI FPGA Module for FlexRIO.

  • 16-Bit, 1 MS/s, 32-Channel Signal Generator Adapter Module for FlexRIO

    NI-5742 / 782865-01 - NI

    The NI‑5742 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5742 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5742, you must pair it with a compatible PXI FPGA Module for FlexRIO.

  • 16-Channel DAC FMC Module

    FMC216 – HPC - Sundance Multiprocessor Technology Ltd.

    The FMC216 is a sixteen-channel DAC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC216 provides sixteen D/A 16-bit 312.5Msps (2.5Gsps with x8 interpolation) channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC216 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.

  • 16 Inputs, 12 Outputs, 2RU:

    SPN1612 - Lectrosonics, Inc.

    From small installations all the way up to sophisticated, multi-layered systems, these ASPEN mixers are the perfect compliment to your audio integration. Unlimited input expansion and 48 mix buses give you phenomenal scalibility. The Proportional Gain Algorithm provides seamless auto-mixing and integrates easily with with echo cancellation, analog mixing consoles, or any other type of audio system. And with TCP/IP addressibility for control through Ethernet, ASPEN is now part of your network.

  • 16 Inputs, 24 Outputs, 2RU:

    SPN1624 - Lectrosonics, Inc.

    From small installations all the way up to sophisticated, multi-layered systems, these ASPEN mixers are the perfect compliment to your audio integration. Unlimited input expansion and 48 mix buses give you phenomenal scalibility. The Proportional Gain Algorithm provides seamless auto-mixing and integrates easily with with echo cancellation, analog mixing consoles, or any other type of audio system. And with TCP/IP addressibility for control through Ethernet, ASPEN is now part of your network.

Get Help