Showing product results. 4336 - 4350 of 7007 products found.
-
ST05 - General Technologies Corp.
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Acces I/O Products, Inc.
High performance PCI Express (PCIe) data acquisition and control cards from ACCES are now shipping. Choose from analog, digital, and serial I/O cards for your next application. The bandwidth of PCI Express (PCIe) is more than double that of PCI in a x1 slot and also features both hot-swap and hot-plug installation. If you don't see what you need, ask us and we will make it for you.
-
Concerto - The Phased Array Company
Concerto is a UT acquisition and analysis software specially designed for Phased Array corrosion mapping. For the tough field conditions that operators deal with Concerto features no menu, less than 18 icons, and few controls so that operators can easily work and not be bothered by complex GUIs. Concerto is simple and easy to work with yet WT, Surface, and back wall C-scan can still be analyzed and setting can be changed using the same acquired data.
-
PI-250B - ETI Precision
The PI-250B Portable Current Power Supply provides unequaled capability in a portable package. The PI-250B generates continuous current of 250 amps with peak maximum output 750 amps through a breaker and 1000 amps into a short, all on 120 VAC supplies. The unit weighs no more than 35 pounds, allowing easy mobility. Basic operation is very simple, and the proven instrumentation provides optimal output control and measurement.
-
900PB Series - Acromag, Inc.
Each module provides a direct network interface for your I/O signals. Unlike "block I/O" devices that combine large, expensive processor blocks with snap-on I/O terminal blocks, 900PB modules handle the network interface and I/O processing in one, compact multi-channel module. This space-saving approach is very cost-effective for systems that need to add a small quantity of I/O channels at existing control sites or network to new remote sites.
-
Acroname, Inc
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
Pepperl+Fuchs GmbH
Inductive proximity sensors are the preferred choice for the majority of applications requiring accurate, non-contact detection of metallic objects in machinery or automation equipment. As a pioneer and market leader, Pepperl+Fuchs offers innovative, high quality inductive sensors to meet the needs of the worldwide automation and process control markets. Our experience, flexibility and customer focus continues to allow us to offer custom designed solutions for the most unique and demanding applications.
-
TE5100-PCI - TEAM SOLUTIONS, INC.
The TE5100 is a 100MHz Direct Digital Synthesized Signal Generator available in a 3U, CompactPCI or straight PCI format. The TE5100 generates Sine and ACMOS/TTL output signals simultaneously up to 100MHz in 1 µHz steps. Sweep, FSK, Chirp and Single Tone are generated on board. The virtual panel allows control up to 100MHz of all parameters. The TE5100 is equipped with a ±1ppm on-board TCXO clock and can accept an external clock source.
-
T-510 - Techno Instrumentation (India) Private Limited
Pulse Echo, Impulse current and Decay methodprovided to get the distance to almost all typesof faults.Laptop based 15 inch display with user friendlyinterface for easy operation.Online support of experts to review fault graphs.Comparison feature of any 5 graphs for reviewand analysis to get more accurate results.Velocity of propogation(VOP) control makes iteasy to precisely pre-locate faults in cables withdifferent velocity.Automatic storage of more than 10,000 faultgraphs.
-
Bender Inc.
Neutral Grounding Resistors (NGRs) are used to limit the maximum ground-fault current. Restriction of fault current lowers hazards and reduces damage done to equipment. High Resistance Grounding (HRG) systems are often used on industrial and critical power applications to maintain system uptime during a first ground fault. HRG systems are also used in tripping applications to help control touch potential on portable loads and improve personnel safety.
-
RDP-20C - TEGAM Inc.
TEGAM''s Humitran duct probes provide a reliable, accurate, and low cost method for monitoring relative humidity plus temperature. Solid state sensors supply excellent sensitivity, fast response and long term stability. Simple hook up and linearized output permit interfacing with most display or control devices. Model RDP-20C outputs a 4-20 mA current loop for long virtually unlimited cable distances.
-
Ocular - Teledyne Photometrics
Ocular is our capture control software, designed to make it as easy as possible to capture, save and publish images and movies without fuss. Designed with a modern windows ribbon interface Ocular allows users of color and monochrome cameras to capture high-quality images and videos from their microscope or lens system. Our movie capture tools are extremely advanced offering multiple ways to view and capture time-lapse or high speed movies.
-
IMS 7f-Auto - CAMECA
The IMS 7f-Auto is the latest version of our successful IMS xf Secondary Ion Mass Spectrometer (SIMS) product line. Designed to deliver high precision elemental and isotopic analyses with increased ease-of-use and productivity, it has been optimized for challenging applications such as glass, metals, ceramics, Si-based, III-V and II-VI devices, bulk materials, thin films... fulfilling industry requirements for efficient device development and process control.
-
Metrix
Seismic sensors provide a dynamic AC signal output in mV/g or mV/in/sec. Devices with this type of output are generally intended for connection to a stand-alone vibration monitoring system rather than general automation and control instrumentation like a PLC or DCS. Metrix offers seismic sensors with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
-
cRIO-PN-S / 782131-01 - NI
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory … control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
