Showing product results. 4276 - 4290 of 6959 products found.
-
cRIO-9055 / 787879-01 - NI
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9055 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an … Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Keysight Technologies
Meet changing requirements in ATE and production test with up to eight easily swappable modules per mainframe. The modular design conserves rack space and simplifies system cabling and assembly. Modular system permits up to 8 outputs of 150W per output in 4U of rack space Simplify reconfiguration, calibration, or repair with modules that remove from the front without disconnecting DUT wiring GPIB interface with SCPI command set, drivers available Serial link system enables control of multiple power supplies from one GPIB address Simplify system cabling when isolation or reverse voltage is needed using optional built-in open/close/polarity reversal relays Advanced hardware and software triggering system to allow synchronization to other events in your ATE system Simplify cabling with built-in measurements Streamline tasks with optional keyboard for manual control and advanced programmable features including automated sequencing of up to 20 output setting steps Ensure DUT safety with protection features
-
Ono Sokki
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
MXI-4 Series - Marvin Test Solutions, Inc.
The MXI-4 PXI Bus Expanders allow direct control of PXI systems from any PCI slot in a desktop computer or server. MXI-4 interface cards can also be used to link multiple PXI chassis. MXI-4 technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
MXI-4E Series - Marvin Test Solutions, Inc.
The MXI-4E PXI Bus Expander allows for direct control of PXI systems from a PCI or PCIe slot in a desktop computer or server. MXI-4E interface cards can also be used for linking multiple PXI chassis. MXI-4E technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
MS332 - Electro-Sensors, Inc.
Modes include zero-cumulative-error Ratio-Follower (electronic gearing) and zero-cumulative-error Index-Follower (mechanical event/phase synchronization). Features include Forward-only and Forward/Reverse settings for uni/ bi-directional control, multiple setpoints and many programmable contact-closure input and NPN output functions. Builds numerous machine synchronizing / follower processes. Works with quadrature incremental shaft encoders (all modes) and prox, photo-eye and other presence/event sensors (Index-Follower mode).
-
Xcelera-CL+ PX8 Full - Teledyne DALSA
The X64 Xcelera-CL+ PX8 Full has been built within Teledyne DALSA’s Trigger-to-Image Reliability technology framework. Trigger-to-Image Reliability leverages Teledyne DALSA’s hardware and software innovations to control, monitor and correct the image acquisition process from the time that an external trigger event occurs to the moment the data is sent to the host, providing traceability when errors do occur and permitting recovery from those errors.
-
CG-971 - Texio Technology Corp.
* Analog video signal/Audio signal output * Conformity with NTSC,PAL,PAL-M and TNSC-4.43 * Selectable sync level * Available for various and output patterns by system file* Each staircase level in step pattern settable by voltage * Natural image and Monoscope pattern output * Max. 24 pattern installation * Auto sequence mode * GP-IB, RS-232C, and Digital IF (TTL) for remote control * Half rack size of 19 inch EIA 2U
-
Multi-CE5 - Hilo Test
The Multi-CE5 includes an Electrical Fast Transient Generator (EFTG), a Combination Wave Generator (CWG) and a Coupling-/Decoupling Network (CDN) for single-phase power supply lines. The software program CE-REMOTE allows full remote control of the test generator via Ethernet light guide as well as recording, evaluation and documentation of test results, according to IEC 17025. To record the wave shape of impulses, it is equipped with an Impulse Recording Function (IRF).
-
11250 - M. C. Miller Company
Comes loaded with M. C. Miller's Test Site Survey application• Integrates with ProActive, M. C. Miller's corrosion control data management application• Data-types are customizable for each of your test sites and each test site can be GPS position stamped • High-resolution date/time stamped photos can be taken at your test sites during a route and recorded images are posted directly to the ProActive database • Sub-meter GPS position resolution
-
Nano DSC - TA Instruments
The Nano DSC differential scanning calorimeter is designed to characterize the molecular stability of dilute in-solution biomolecules. The Nano DSC obtains data using less sample than competitive designs. Solid-state thermoelectric elements are used to precisely control temperature and a built-in precision linear actuator maintains constant or controlled variable pressure in the cell. Automated, unattended continuous operation with increased sample throughput is achieved with the optional Nano DSC Autosampler.
-
ZET 7012-I VER.3 - ZETLAB Company
Digital gauge pressure ZET 7012-I VER.3 (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER3 digital gauge pressure meter is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.
-
Series 5000 - Eastern-Optx
Eastern OptX introduces moving target generators covering radar frequencies from 1 – 18 GHz. These compact systems provide target generation with speeds from 0 to 3000 MPH, and allows the user to set target and radar source speeds and directions. Systems may be operated remotely using wireless control with scenario generator features including flight path replication, moving source and targets, and multiple target options.
-
PICAM Driver - Teledyne Princeton Instruments
PICam is the driver for controlling all Teledyne Princeton Instruments cameras and is the platform on which LightField software is built. Teledyne Princeton Instruments also offers the PICam API, which can be used to directly automate any Teledyne Princeton Instruments cameras using the C run-time. This, alongside the PICam SDK, provides efficient and direct control of all cameras. It is available for 64-bit Windows and Linux systems (see Hardware Requirements for details).
-
K-Series - Mountz Inc.
The K-Series are low voltage DC electric screwdrivers. These rugged assembly tools increase productivity and enhance product quality through precision torque control and user comfort. The electric screwdrivers automatically stop when the preset torque has been reached. The K-Series electric screwdrivers are NRTL certified from TUV America, Inc. The certification ensures manufacturing companies that they are purchasing and operating a quality and safe tool for its operators.
