Filter Results By:

Products

Applications

Manufacturers

Control

Known value


Showing product results. 1816 - 1830 of 7035 products found.

  • PCI Synthesizer

    SYNTH300 Series - Furaxa, Inc.

    These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.

  • PCI Three-Axis Laser Board

    N1231A - Keysight Technologies

    The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).

  • Photovoltaic Array Simulator, 15 kW, 1500 VDC

    N8900APV Series - Keysight Technologies

    The PV simulators are autoranging, programmable DC power sources that simulate the output characteristics of a photovoltaic array under different environmental conditions (temperature, irradiance, age, cell technology, etc.) enabling you to quickly and comprehensively test inverter MPPT algorithms and inverter efficiency. The DG8900 SAS control software creates and downloads solar I-V curves to a single output solution. For multiple outputs choose the DG9000 SAS control software which can be used with up to 12 N8900APV sources.

  • Power Amplifier/Supply

    677B - TREK, INC.

    The Trek Model 677B is a high-voltage power amplifier/supply unit for precise control of output voltages in the range of 0 to ±2 kV DC or peak AC with an output current range of 0 to ±5 mA DC or peak AC. The Model 677B can be operated in one of two modes: as a high-voltage amplifier where it is configured as a noninverting amplifier with a fixed gain of 200 V/V, or as a high-voltage power supply which responds to front panel controls to command an exact output voltage or current.

  • Power Management & MMI module

    H73000700 - 6TL Engineering

    This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.

  • Preset Torque Screwdrivers

    TLS Prime - Mountz Inc.

    The TLS Prime is a new economical preset torque screwdriver series. Designed with same the trusted Mountz cam-over technology, the TLS Prime provides the basic elements required for preventing over torque occurrences. The screwdriver is designed for industries with low volume fastening applications or have less stringent torque control requirements. Engineered with a durable plastic cam mechanism, the preset screwdriver (internally adjustable) still provides precision torque control and prevents a fastener or bolt from being under and overtightened.

  • Salt Spray Chambers

    Dongguan Amade Instruments Technology Co., Ltd

    Salt spray chamber is intended to use method of salt-spray corrosion to evaluate the performance of corrosion resistance of specimens to salt fog under the specified conditions. It is capable of simulating a locally salt mist environment in which the test piece is placed. There are different types of salt fog chambers including microprocessor digital version, touch-screen control version and compound version featuring temperature&humidity control and adjustment. widely applied to components and parts, electronics elements, metal materials etc.

  • Thermoelectric Cooler Controller

    Analog Devices Inc.

    Analog Devices Thermoelectric Cooler Controllers work with cooler based photonics, offer the smallest size, the best efficiency and the most robust solutions. It has a linear power stage with the linear driver output and a pulse width modulation power stage with the SW output. Depending on the part number, it offers digital PID control or analog PID control or both. Our TEC controllers support a variety of MSA based optical modules such as SFP, SFP+,QSFP+, CFP/CFP-2/CFP-4 and QSFP28.

  • Time Domain Replication (Road Load Simulation)

    M+P International

    The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.

  • VME PWM Servo Motor Driver / Amplifier Board

    64PW2 - North Atlantic Industries

    NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).

  • Test bench for Diagnostics of Brake Valipers

    MS300 - MSG Equipment

    Diagnostic equipment MS300 for repair and diagnostics of brake calipers. MS300 is manufactured fromanti-corrosion materials resistant to chemical effects of the brake fluid. The tabletop and the control panel are made of stainless steel, itensuresa long-lasting service of the equipment. A pressure indicator andhigh-pressure pumpcontrol elements are located on the control panel. There is also aconnection coupling fortested units. There is a gutter along the tabletops perimeter preventing the brake fluid from draining on the floor. For convenient use of tools, there is a section with perforation on the back side.

  • 4 2/3 Digital Potentiometer Meter

    CS2-PM - Chuan Sheng Electronics Co., Ltd.

    CS2-PM Potentiometer Indicator has been designed with high accuracy measurement, display and communication of Ohm (3 wire) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.

  • Digital I/O PXI Card

    GX5290 - Terotest Systems Ltd.

    The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.

  • 1.9 GHz Intel Celeron Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller

    IC-3171 / 784963-01 - NI

    The IC‑3171 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in … extreme environments. The IC‑3171 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.

  • HUSKIE 2.0 roboRIO MXP Expansion Board

    FRC3061-MXP2-R1 - Playing With Fusion Inc

    The Huskie Board, designed by FRC Team 3061, is an FRC qualified expansion board for the NI roboRIO robotics controller. In addition to breaking out all available signals on the MXP expansion port, this board uses a Parallax Propeller IC (8 symmetrical logical cores with shared memory and peripheral access) to enable tasks such as advanced data logging, on-field driver control and status, and NeoPixel control. Additional GPIO and analog inputs are added with open source code to allow further customization.

Get Help