Filter Results By:




Showing recent results 856 - 870 of 974 products found.

  • Electronic Load


    * Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.

  • HEV & EV Power Tester

    EVd-40 - NuVant Systems, Inc.

    The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.

  • LC Software

    LabSolutions CS - Shimadzu Corp.

    LCs and GCs are used extensively in quality control and research and development departments in a wide range of industries, including pharmaceutical, chemical, and food. Recently, an increasing demand for food safety and environmental analysis and measurement has led to a dramatic increase in the number of samples being analyzed which, in turn, has resulted in demands for faster, easier-to-use instruments and software. In the pharmaceutical industry, compliance to regulations and guidelines, such as CSV and PIC/S GMP, U.S. FDA 21 CFR Part 11, Data Integrity and so on, and the proper, efficient management of instruments and analytical data are required. With this background, faster, more efficient management of instruments and data is essential. LabSolutions is a network-compatible analysis data system capable of meeting these needs.

  • Lock-in Amplifier

    UHFLI - Zurich Instruments AG

    The Zurich Instruments UHFLI is a digital lock-in amplifier covering the frequency range from DC to 600 MHz. In addition of providing the highest operation frequency amongst all commercial lock-in amplifiers, the UHFLI also offers the lowest time constant of 30 ns for demodulation, resulting in a demodulation bandwidth of more than 5 MHz. The exquisite analog front end offers a spectacular noise performance of 4 nV/Hz which helps in many applications to keep the signal-to-noise ratios high while speeding up the measurement. In combination with the most innovative instrument control software LabOne, the UHFLI is the flagship of all Zurich Instruments products and represents the state of the art of today''s scientific instrumentation.

  • Low Profile PCI Express 8-Port

    7803e - Sealevel Systems, Inc.

    The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.

  • Multi-Channel X-Ray Fluorescence Spectrometer

    FACTORY LAB MXF-2400 - Shimadzu Corp.

    Wavelength Dispersive X-Ray Fluorescence Spectrometer The Shimadzu MXF-2400 is an improved version of the Shimadzu Multi-Channel X-ray fluorescence spectrometer, which has been rated highly in the overseas market as well as in the Japanese market. The latest hardware designed to fully utilize the principle of X-ray fluorescence spectrometry and the data processing unit that uses various software programs to permit automatic management of analysis data combine to provide high analytical productivity both in R&D and production control. Up to 36 elements can be simultaneously determined by the fixed monochrometer and up to 48 elements can be determined sequentially by the optional scanning monochrometer. High analytical precision is provided even in high sensitivity analysis of a few ppm quantity level.

  • PXIe, 32 AI (16-Bit, 500 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module

    PXIe-6349 / 785808-01 - NI

    PXIe, 32 AI (16-Bit, 500 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe-6349 offers analog I/O, digital I/O, and four 32-bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the … high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6349 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.

  • Wireless Day/Night IP Surveillance Camera

    ENVIROMUX-IPCAM-WN - Network Technologies Inc

    View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.3 mm (0.17 in), 12 infrared LEDs for night vision. RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.

  • Enterprise Voice & Data Processors

    Macom Technology Solutions Holdings Inc.

    Macom offers a line of infrastructure voice processors, in concert with the carrier-grade Media Stream Processing software, that delivers complete, integrated VoIP media, data and fax, signaling and control processing solution. Combined with powerful DSP cores with flexible packet processing engine and a rich set of interfaces, the processors support 8 to 32 channels of packet-TDM and packet-packet operation across the entire range of IP modulations, for VoIP and Data applications. Major applications include Enterprise voice gateway PBX, Enterprise class WAN router, Firewall, VPN routers, high speed 802.11 access point, integrated access device, packet voice enabled IP router, IP enabled PBX.

  • PWM to Voltage Output D/A Converters

    Analog Devices Inc.

    Analog Devices’ pulse-width modulation (PWM) to voltage output D/A converters convert a PWM input to an accurate, stable, buffered voltage without the ripple, slow settling, and external passive components of discrete filter implementations. Our PWM D/A converters measure the period and pulse width of a PWM input signal and immediately update the D/A converter output with up to 12-bit accuracy and no software coding required. This family of D/A converters is available with 8-bit to 12-bit resolution, dual and quad channels, integrated references, and with high temperature operation. Applications include isolated motor control, automotive headlights or industrial lighting, and other applications that benefit from the simple control interface.

  • High Resolution, High Sensitivity, High Stability ICP-OES Spectrometer

    Ultima Expert - HORIBA, Ltd.

    HORIBA Scientific develops and manufactures high performance ICP-OES spectrometers for more than 35 years. The new Ultima Expert is a unique combination of ultimate performance with comprehensive assistance tools designed to simplify method development. Ultima Expert integrates high efficiency Jobin Yvon optical design capable to achieve optimal performance for a large variety of sample types and matrices.Ultima Expert is driven by the powerful Analyst software featuring a large variety of analytical functionalities for tailored control and analysis. The robustness of the Ultima Expert makes it ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical, metallurgical production and precious metal refining.Gain in efficiency with the Ultima Expert for your most demanding needs!

  • Affordable ICP-OES Spectrometer

    Ultima Expert LT - HORIBA, Ltd.

    HORIBA Scientific develops and manufactures high performance ICP-OES spectrometers for more than 35 years.• The new Ultima Expert LT provides high performance at affordable price for laboratories with challenging samples.• Ultima Expert LT integrates high efficiency Jobin Yvon optical design capable to achieve optimal performance for a large variety of sample types and matrices.• Ultima Expert LT is driven by the powerful Analyst software featuring a large variety of analytical functionalities for tailored control and analysis.• The robustness of the Ultima Expert LT makes it ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical and metallurgical production• Gain in performance with the Ultima Expert LT for your most challenging applications!

  • Automatic Asphalt Content Tester

    Atico Export

    4000g sample capacity, integrated +0.1gm accuracy weighing scale, High temperature ceramic filtration system and afterburner for accurate measurement of bitumen content in asphalt mixes. Automatic operation through user defined automatic end point detection and 24 hour start timer. User defined control of furnace chamber temperature from 200 – 650oC, Digital display and printing of test data through bright LED displays and integrated printer, Software activated mechanical door lock to prevent door from opening during test process and cutting off power from the heating elements upon opening the door. Operates on Single Phase, 220V, 50 Hz, 20 Amp and consumes less than 5000 W.

  • Digital I/O Board, 32 Isolated I/O Channels, 24V


    The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.

  • GPIB Instrument Control Device

    GPIB-RS485 / 779733-04 - NI

    Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 … serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.

Get Help