Filter Results By:

Products

Applications

Manufacturers

Showing recent results 796 - 810 of 974 products found.

  • 2-Channel 400MHz DDS Signal Generator

    2940A - Novatech Instruments , Inc.

    The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.

  • 32-Channel, ±30 V, Sink Outputs, Bank-Isolated Digital I/O Device

    PCI-6517 / 779083-01 - NI

    The PCI-6517 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6517 module is an industrial digital I/O … interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6517 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.

  • 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device

    PCI-6516 / 779082-01 - NI

    The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O … interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.

  • Automation System

    1000 OTDR - Photon Kinetics

    The 1000 OASYS OTDR Automation System is a complete test station for optical fiber cables that is capable of testing over 1000 fibers in an 8 hour shift (bi-directional, 3 wavelengths). The system is comprised of the 8000 OTDR, the fastest, most accurate OTDR for cable testing, the 1001 Multiple Fiber Handler, which provides automated, highly reliable temporary coupling of the cable's fibers to the 8000, and the OASYS.net OTDR Automation Software that leverages the unparalleled performance of these two products by giving the user the ability to control every aspect of the testing process via an intuitive, network- compatible interface.

  • Board cameras

    The Imaging Source, LLC

    The Imaging Source USB 3.1 (gen. 1) color board cameras combine the latest Sony Pregius and STARVIS CMOS sensor technology with the USB 3.1 reversible Type-C port connection to provide exceptional image quality and easy integration. These single-board cameras measure only 30 x 30 x 12 mm and offer maximum flexibility for a wide range of space-limited applications such as industrial automation, quality control, surveillance and medicine. The included software allows for the adjustment of gain, exposure, frame rate and white balance. Specific models are available with a variety of input, output, strobe and trigger options.

  • Calibrators

    Orbit Controls AG

    Orbit Controls calibrators are suitable as signal sources for the test field or the laboratory. They can be used as generators for calibrating and testing electronic measuring devices or assemblies both by manufacturers and by companies that have to carry out periodic calibration tasks due to the quality certification. They are also used in laboratories, development departments, repair and calibration services and much more. In addition to manual operation, all devices also have an RS232 or IEEE interface so that the calibrators can be integrated into an automatic measuring station. To calibrate multimeters with an LCD display, a camera is used which scans the display and automatically integrates the measured values ​​into the calibration software.

  • Compact HD Thermal Camera

    FLIR A8580 MWIR - Teledyne FLIR

    FLIR A8580 MWIR cameras provide the crisp imagery, accurate temperature measurement, and streamlined analysis features needed for industrial, military, and manufacturing R&D applications. The 1.3 MP detector produces high definition thermal images, while the suite of manual and remote focus lenses allow users to maximize the number of measurement pixels on their target. Simple, single cable connectivity using Gigabit Ethernet or CoaXPress provides complete camera control plus data capturing in FLIR Research Studio software, so users can analyze and understand data faster than ever before.

  • Compact LWIR HD Thermal Camera

    FLIR A8580 SLS - Teledyne FLIR

    FLIR A8580 LWIR SLS cameras provide the crisp imagery, accurate temperature measurement, and streamlined analysis features needed for industrial, military, and manufacturing R&D applications. Thanks to the 1.3 MP Strained Layer Superlattice (SLS) detector and the suite of manual and remote focus lenses, users can maximize the number of measurement pixels on their target. Simple, single cable connectivity using Gigabit Ethernet or CoaXPress provides complete camera control plus data capturing in FLIR Research Studio software, so users can analyze and understand data faster than ever before.

  • Data Acquisition Unit

    KiDAU - Kistler Instrument Corp.

    A KiDAU Classic System has 32 analog and 16 digital inputs. The application of different connectors as well as pin assignments for the 32 analog inputs will be mapped by means of different SD-panels. Each analog channel comprises a programmable input amplifier, bridge excitation circuit, low pass filter and 16 Bits A/D converter. The amplifier precision is better than 0,1 % and the input impedance above 10 MΩ. The gain values can be programmed from 0,5  ...  10  000. An internal reference voltage is used for precise control of the amplifier setting, which is achieved via software loop.

  • Data Loggers

    ThermoWorks

    ThermoWorks temperature and humidity loggers are perfect for food processing, transportation, and restaurant fridge and freezer storage, including cold chain management, cook chill, and critical control points (HACCP). They are also used in labs and for pharmaceutical applications like VFC. Wirelessly pair multiple network-connected units to a single base station through WiFi, Bluetooth, or RF and store your temperature or humidity readings in the cloud. Our USB probes and USB data transfer loggers are also popular and come with integrable software. Specialized loggers are also made for harsh environments, including extreme low and high temperatures.

  • Gavia AUV Software and Data Handling Software

    Teledyne Marine Gavia ehf.

    ​The Gavia autonomous vehicle control software is implemented using a 'crewmember' paradigm. This means it is organized using a distributed architecture modeled on the division of responsibilities among the crew of a marine vessel. The Gavia Intelligent Artificial Crew (IAC) comprises a full set of modules responsible for the safe navigation of the vessel together with project modules responsible for meeting the goals of the mission. The Captain has the a set of responsibilities suitable for the role; overseeing the operation of the vessel and deciding on actions in response to exceptional or critical circumstances. With the vehicle Captain handling reaction to exceptional circumstances, the application modules are free to concentrate on the goals of the mission.

  • High Voltage System

    HV-2 - International Electro-Magnetics, Inc.

    *Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.

  • Intelligent Power Monitor

    iPM - North Atlantic Industries

    NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.

  • Osprey / DX Co-Processor

    9687 - Strobe Data Inc.

    Double+ speed Osprey Co-Processor. Occupies one ISA/EISA PC slot. Writable control store, FPGA implementation of PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent twice the DCJ-11® and 100%; of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. This card is used for Osprey/PC applications where all applicable I/O devices are emulated on the PC by Osprey software. Includes standard environment support for MS-DOS® V6.2.2. Windows/NT® environment support available.

  • PCIe Direct Digital Synthesizer

    Furaxa, Inc.

    These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.

Get Help