Filter Results By:
Products
Applications
Manufacturers
Contact Resistance
opposition to the flow of heat or electricity within a connection.
- CAMI Research Inc. (CableEye®)
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
CAMI Research Inc. (CableEye®)
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.
-
product
Contact Resistance Tester
JYL
As a high current passes through a pair of mechanically independent metallic contacts, the contact resistance must be as low as possible. Increasing the contact resistance of the contact often causes a large voltage drop on the contact, which reduces the input power of the load equipment. If the contact resistance of one or two contacts becomes large, the three-phase voltage of the load equipment will be unbalanced, causing phase loss operation.
-
product
Contact Resistance Tester
JYL-200B/100B
Product description: JYL-200B/100B contact resistance tester can measure contact resistance of high voltage switches and circuit breakeres, also can test primar side resistance of transformer and grounding wire in groups
-
product
Contact Resistance Tester
CRM-200
Contact Resistance Meter CRM-200 can provide test current up to 200A subject to the load resistance and supply voltage, which is suitable for testing circuit breaker contacts, switch contacts, busbar joints or other applications where high current is needed.Contact Resistance Meter CRM-200 uses a four terminal measurement method to eliminate the resistance of the test leads from the measurement.
-
product
Contact Resistance Meter
CRM-100
Contact Resistance Meter CRM-100 is capable of providing test current up to 100A subject to the load resistance and supply voltage. It can be used to test circuit breaker contacts, switch contacts, busbar joints or other applications where high current is needed.
-
product
Contact Resistance Meter
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
product
Contact Resistance Meter
CRM 100C
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
product
Contact Resistance Meter
CRM 200B
CRM 200B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions.CRM 200B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.
-
product
Contact Resistance Meter
CRM 100B+
SCOPE introduces its next generation of hugely popular CRM series contact resistance meter, CRM100B+ in all new super light avatar, based on cutting edge ultra capacitor technology. CRM incorporates some state of the art hardware & smart software features making it a must have tool for testing & maintenance engineers.
-
product
Contact Resistance Measurement
CRM 100B
CRM 100B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions. CRM 100B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.
-
product
Contact Resistance Meter
PCRM200S
The Motwane Manufacturing Company
The Motwane make Contact Resistance Meter (Model:PCRM200S) is a digital micro-ohmmeter, specially designed to measure extremely low resistance in micro ohm. The Instrument is based on Kelvin 4-wire connection method for measurement of low resistance.The Current injection is fixed at 100A & 200A. Test information like current injected with measured resistance & voltage drop is displayed with real time data on large LCD with backlit.This User friendly Instrument and it's accessories are housed in easy transportation case. Advanced Windows based software isprovided for data downloading, analysis and report generation. Internal memory of 199 records is provided for onsite data storage withDate & Time stamping & Recalling facility. Thermal printer is the additional feature provided to print the test results.
-
product
Contact Resistance Meter
CRM 200B+
CRM directly measures micro-ohm values at 200A DC under live EHV switchyard conditions quickly & accurately. It is specially designed to reliably measure micro-ohm contact resistances of Circuit Breakers, Isolators, Busbar joints, earth switch joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards up-to 765 kV. SCOPE’s ability to make electronics work in such environment enables CRM to measure mili-volts signal in the presence of kilo-volts noise.
-
product
Contact Resistance Meter
4.5 Digits LED display Range : 0 TO 1999.9 W to 199.99mW High Measurement Current : 100A DC max. True Four wire resistance measuring technique eliminates lead resistance errors inherent in 2 wire systems. Fully protected against overloads. Proven design
-
product
Contacts Resistance Tester
JYK II
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
product
Dynamic Contact Resistance Meter
Dynamic contact resistance measurements are necessary to understand the condition of the arcing contacts of the circuit breaker. Static contact resistance measurements do not give us information related to erosion of arcing contact, misalignments of the contact, and damages to the driving mechanism.
-
product
Handheld Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The hand-held Circuit resistance tester is an innovative product. The product is compact, hand-held operation, battery power supply, easy to carry. The product is mainly used in the measurement of contact resistance and other micro-Euclidean resistance of switch contacts. The test speed is fast and the accuracy is high.
-
product
Auto Contact Resistance Tester
KVHL
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
product
Contact Resistance Test Sets
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
-
product
Earth Contact Resistance Tester
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
product
Contact Resistance Measurement System
CRMS
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
-
product
Contact Resistance Measurement Kit
LRM-10
The LRM-10 is a 10A micro-ohmmeter kit designed to measure low resistance for electrical interconnections integrity testing. The LRM-10 has a range from 0.01µΩ to 200Ω. It comes with heavy duty four points probes and it is compatible with a great variety of optional accessories.
-
product
Circuit Breaker Contact Resistance Meters
Vanguard Instruments Company, Inc.
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field.
-
product
Hand Held Sheet Resistance Measurement Instrument[Replaceable Probe Set (Non-destructive Probe & Contact Probe) ]
DUORES
Easy to measure sheet resistance & carry aroundReplaceable hand-held probes for Non-destructive & Contact type
-
product
Micro Coax, Patchcord, Receiver, 36", 50 GHz, Flex 405, to 2.4 MM Plug
7-371105764-036
Micro Coax, Patchcord, Receiver, 36", 50 GHz, Flex 405, to 2.4 MM Plug.
-
product
Pneumatic, Contact, Receiver, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610131101
Primary mating contact 610132101.Pneumatic Contacts are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
product
Pneumatic, Contact, Receiver, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610131104
Primary mating contact 610132104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
product
Mini Fiber Optic, Contact, ITA, Multimode
610113173
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
product
Mini Pneumatic, Contact, ITA, Plug, Fits Mini Coax/ Mini Power modules
610132110
Mini Pneumatic, Contact, ITA, Plug, Fits Mini Coax/ Mini Power modules.
