Antenna Test
See Also: Antenna Measurement, Test Ranges
-
product
Antenna Test Chamber
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
product
CATR Benchtop Antenna Test System
ATS800B
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Antenna Test Chambers
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
product
Rapid Antenna Testing Services
At JEM we understand the challenges facing antenna, microwave and communication system engineers, and we realize that accurate measurement of antenna electrical performance is critical. That’s why we offer a range of rapid antenna testing services from 50 MHz to 40 GHz.
-
product
Low Noise Pre-Amplifiers
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Shielding Solutions
Antenna Test Chambers are especially designed for testing RF devices and antennas from frequency ranges of 700 MHz to 6000 MHz. These Antenna Test Chambers provide a shielding of more than 90 dB as well as lowest residual passive intermodulation.
-
product
Compact Range Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Antenna, Biconical
EM-6917B-1 | 30 MHz To 3 GHz
The EM-6917B-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 3 GHz, the EM-6917B-1 eliminates the need for adjustments or switching antennas in most test applications up to 3 GHz, and it does so without compromising power handling capability for transmit applications.
-
product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Testing Large Radar Sensors with CATR Technology
CATR Radar Test System UTP 5069
Modern driver assistance systems must recognize increasingly complex traffic scenarios and convert them into appropriate vehicle reactions with the help of artificial intelligence (AI) and specific algorithms. Imaging radar sensors with a higher spatial resolution, so-called imaging radar sensors, are therefore required. These can better distinguish larger from smaller objects and, due to the larger antenna apertures, also require larger dimensions of the test environment or larger far-field distances. Testing these sensors in the direct far field ( UTP 5065 ) would therefore require very large absorber chambers up to ten meters in size and more.Our efficient test system UTP 5069 offers exactly the right solution:By using CATR technology (Compact Antenna Test Range), 4D, imaging and other radar sensors with large far-field distances are calibrated with high precision in a small footprint. With the extremely low-reflection NOFFZ absorber chamber, the system is very well suited not only for validation, but also for EOL tests.
-
product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
product
Antenna Test Chamber for Automotive Radar
ATS1500C
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
product
Standard Gain Horns
Standard gain horns can be used to experimentally determine the gain of other antennas by using the substitution method. The standard gain horn and the antenna under test are alternately connected to a well matched detector system in order to compare their relative power levels. The power level difference is then added to the appropriate level of the calibration curve to determine the absolute gain of the antenna under test.View more Standard Gain Horn Antennas
-
product
Rack based antenna test system
R&S®ATS800R CATR
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Test Antennas
Lumistar provides small, lightweight portable fixed antennas for Test applications. They are available in lower L thru S bands for transmit and receive applications.
-
product
Antenna Test Facility
Raytheon’s Antenna Test Facility (ATF) provides state-of-the-art measurement capabilities to assist in the development of advanced antenna technologies for a variety of airborne and space applications such as advanced radar and communication systems. The ATF is available for use by Raytheon businesses as well as other companies that design and prototype new and experimental antennas.
-
product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
product
PNA-X Measurement Receiver for Antenna Test
N5264B
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
product
High Gain Horn Antenna
BBHA 9120 K
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009.
-
product
Cable & Antenna Analyzer
CAA-100
ShinewayTech® CAA-100 cable & antenna analyzer can test Return Loss and VSWR of load’ frequency. Also can get Return Loss, VSWR of DTF (distance-to-fault) and Cable Loss. Users can be easy to know the connection of cable & antenna system is reliable whether or not. CAA-100 series with frequency range 25MHz-4GHz and 60dB dynamic range can suitable for 2G/3G/4G/WiMAX system etc. CAA-100 series is the necessary measuring instrument for the new generation of wireless network development, upgrade and maintenance.
-
product
Saluki S5105 Series Microwave Analyzer (SA/VNA/CA)
S5105 series microwave multifunctional analyzer has the wide frequency range from 30kHz to 40GHz. It integrates multiple functions such as dual-port vector network analysis, cable and antenna feeder test, vector voltage measurement, spectrum analysis, field strength measurement, and power measurement, providing you with powerful comprehensive test capabilities. S5105 series RF analyzer is widely used in the radar performance test and cable TV, wireless communication field.
-
product
Antenna
Woken is dedicated to providing innovative standard and custom antenna solutions that incorporate our leading-edge technologies. We offer a diversified product line for wireless applications. Woken also offers custom engineering design through volume manufacturing services. All our antennas are tested to meet our stringent specifications.
-
product
Near-field Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Active Loop Antenna
AL-130R
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
product
Antenna Test Systems and OTA Chambers
With our well-established experience in innovative solutions based on top-quality engineering, Rohde & Schwarz provides you with leading antenna test systems and OTA chambers.
-
product
Antenna, Biconica-log
EM-6917C-1 | 26 MHz – 1 GHz
The EM-6917C-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 1 GHz, the EM-6917C-1 eliminates the need for adjustments or switching antennas in most test applications up to 1 GHz, and it does so without compromising power handling capability for transmit applications.
-
product
Simulators/Threat Emitters
Antennas for RADAR test, simulation and training are designed for integration into complete threat RADAR simulators for use on combat training and test ranges or in simulators for training and evaluation of RADAR operators, aircrews, air-traffic-control or weather radar applications. All antennas for RADAR simulators have high RF power handling capabilities and generally use pressurized transmission lines. Dual-band, single aperture antennas and a cluster of separate antennas mounted to a single pedestal are ideally suited for RADAR simulators in mobile, fixed, shipboard and airborne environments.
