Interferometers
Combine waves to reveal their properties by measuring the pattern of interference.
See Also: Beam Splitters
-
product
Interferometers
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
-
product
Multiple Axis Interferometers
Interferometers that measure two and three axes can increase accuracy, reduce alignment time and save space in high performance multi-axis systems.
-
product
Laser Interferometers & Calibration Systems
Keysight Technologies is a world leader in the design and manufacture of laser interferometry systems, advanced electronic measurement systems, high-precision optical components, complex monolithic optics (CMOs), and opto-electronic systems design for the most demanding metrology applications. Keysight systems offer high precision in a wide dynamic range, the ability to simultaneously measure a position with multiple degrees of freedom, and the highest accuracy available in both air and vacuum systems.
-
product
Single Axis Interferometers
Linear, single-beam, and plane mirror interferometers measure motion on a single axis.
-
product
Infrared Interferometers
Optical imaging applications are broad and varied. Testing at a system's design wavelength is critical for development, final alignment and qualification.
-
product
Phasecam Twyman-Green Laser Interferometers
PhaseCam dynamic Twyman-Green laser interferometers provide high resolution measurements despite vibration and air turbulence. Dynamic Interferometry® enables PhaseCam laser interferometers to capture full wavefront measurements in as little as 30 microseconds—5000 times faster than conventional phase shifting interferometers. Compact and lightweight, PhaseCams make reconfiguring test setups simple and easy, without vibration isolation.
-
product
Interferometers
* Michelson Interferometer with a stabilized single-frequency He-Ne Laser as scale *Measurement range: up to 80 m *Resolution: 5 pm *Wide acceptance angle (up to ± 22.5°) for ball/hollow cube reflector
-
product
Displacement Measuring Interferometers (DMI)
ZMI Series
This unit measures retroreflector targets for tracking objects moving primarily in one linear dimension or rotating about a fixed point. ZYGO offers a standard and compact size linear interferometer to accommodate different system space constraints.
-
product
Interferometers and Reflectometers for Plasma Diagnostics up to 170 GHz
Elva-1 supplies different solutions for measurement density and temperature profiles of plasma. Our systems are installed practically on all TOKAMAKs over the World.
-
product
Angular Interferometer
10770A
The Keysight 10770A Angular Interferometer is a high accuracy plane mirror interferometer ideal for use in precision calibration applications. Used with the 10771A Angular Reflector in an 5530 Laser Calibration System, the interferometer measures pitch and yaw motions along each axis that a machine tool or measuring machine travels. The system can help quickly locate and evaluate unwanted angular motion.
-
product
Entry-level Price Interferometer for Geometry Measurement of Single Fibers
3D SCOPE-V2
Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.
-
product
Adjustable Mount
10711A
The Keysight 10711A adjustable optics mount makes alignment faster and easier. It is a convenient accessory for the Keysight 10702A linear interferometer, 10706A/B plane mirro interferometers, 10715A differential interferometer, and 10716A high resolution interferometer. Allows for 5 degrees tilt and yaw adjustment.
-
product
SANA Mini Portable Interferometer
CA3005
CA3005 SANA mini is a portable, non contact fiber endface interferometer for single fiber connector. This interferometer has a high performance while the size of the instrument is incredible small. SANA mini need only a USB link to work without any external power supplies. It can test the geometry parameters of single fiber connectors such as radius of curvature, apex offset and fiber height. The data and report are generated in excel format and it is very helpful for management and analysis. SANA mini is a suitable interferometer for field usage.
-
product
Digital Automated Fiber & Ferrule Interferometer For Multi-Fiber Connectors
DAFFI MT
Data-Pixel has developed a cost effective interferometer line for high volumes production without compromising accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI MT to be robust, fast and accurate in order to meet all manufacturing or laboratory environments.
-
product
High-Stability Adapter
10723A
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
1/4-Inch Cube Corner
10713D
The Keysight 10713D is one component of a family of measurement optics that tailor interferometer systems for the physical layout and measurement requirements of individual applications. Configured with appropriate laser head and system electronics, the optics are part of a precise positioning system that improves product quality, increases yields, and facilitates manufacture of precision products.
-
product
Multi-Surface Profiler
Tropel® FlatMaster® MSP
The Tropel® FlatMaster® MSP (Multi-Surface Profiler) is a frequency stepping interferometer that provides fast and accurate metrology for semiconductor wafers up to 300mm in diameter. In seconds up to 3 million data points are collected with sub-micron accuracy enabling total thickness and flatness characterization over the entire surface.
-
product
Digital Automated Fiber & Ferrule Interferometer For Single Fiber Connectors
DAFFI SF
The latest interferometer from Data-Pixel is a cost effective solution for high volumes production, without compromising on accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI SF to be robust, fast and accurate in order to meet all manufacturing or laboratory environments. With the Blink software platform, DAFFI is able to measure the end face geometry on single fiber connectors in a very short time. The Daffi interferometer accessories (flange and adapters) are fully compatible with the Daisi range, allowing the user to limit the costs of the 3D geometry measurement units.
-
product
2.5G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
Automated Interferometer with Floating Pastille Technology
DAISI MT FP
The Daisi MT FP combines the Daisi MT-V3 with the new Floating Pastille fixture technology from DATA-PIXEL (patent pending). This major technological breakthrough for multi-fiber connector fixtures is perfectly suited for highly accurate X/Y endface angle measurements.
-
product
Light Analysis
Welcome to Thorlabs; below you will find links to detectors and instrumentation that measure the various properties of light, a subset of our entire line of photonics products. Thorlabs offers an extensive selection of instruments that measure the properties of light. Our versatile power and energy meters can be used with over 25 different sensors in order to make NIST-traceable power and energy measurements. If the convenience of a meter is not desired, our selection of detectors includes basic photodiodes (uncalibrated and calibrated), photodetectors (biased, amplified, and avalanche), CCD and CMOS arrays, position detectors, integrating spheres, and photomultiplier tubes. The Beam Characterization category contains beam profilers (camera and scanning slit), a wavefront sensor, spectrometers, and interferometers, while the Polarimetery link leads to a selection of instruments used to measure and control the polarization of light.
-
product
Fiber End-face Interferometer
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
product
Laser Interferometer Position Measurement Systems
When built into manufacturing and inspection equipment, a laser interferometer system reports the position or controls the motion of a product platform with more accuracy than any other method. It allows manufacturers to produce precision products from integrated circuits to medical devices to aerospace components that meet the most stringent specifications.
-
product
Interferometer
VFI-200
The FGC range is the complete solution for measuring the dimensions of standard and specialty fiber in both production and R&D environments. FGC-GS – fiber glass geometry for fibers up to 1000 µm diameter.
-
product
Custom solutions
Novacam develops custom interferometric solutions to address particular inspection and imaging needs of specialized applications and OEM markets. Our modular interferometer components offer a superior and cost-effective platform for developing high-performance systems and assemblies. We will collaborate with your application experts to devise the optimal combination of inteferometric (OCT) hardware, non-contact fiber-based sensor probes, and system software.As needed, Novacam engineers: develop customized optical probes and inspection stations develop inline probe fixtures for production environments adapt Novacam standard interferometer component modules to suit your application help integrate Novacam systems or components with third-party tools write customized software
-
product
One Axis Differential Interferometer
10719A
The Keysight 10719A One Axis Differential Interferometer makes either a differential linear or angular measurement for use in single and multiple axis applications. The linear measurement gauges the displacement between two objects, such as a stage and an optical column or inspection tool. The 10719A also measures either pitch or roll. An angle is measured when both reference and measurement beams measure to the same mirror. The 10721A provides high immunity to unwanted interferometer displacement, such as thermal expansion. It is a modular, compact design with monolithic optics for maximized mechanical stability. Use of a small 3 mm beam helps decrease Abb offset error.
-
product
Interferometer
S100|HR
CNC polishing puts new demands on metrology tools. Many of these optics are aspheric with tight tolerances. The new machines can produce almost any surface and require a new level of metrology to provide feedback to the polishing process. This just cannot be done with outdated interferometers designed over 30 years ago. The S100|HR has the performance it takes, without breaking the bank. Measure 10X higher fringe densities to enable final figuring to begin sooner, saving you time and money. Plus measure these high density fringes 5X more accurately to enable large polishing corrections that converge quickly to final figure, including aspheres.
-
product
Create Topographic Profiles from SPM Images
TopoStitch
topoStitch™ offers the easiest and most accurate way to stitch topographic or greyscale images from Scanning Probe Microscopes (SPM’s), profilers, interferometers, confocal microscopes or any other instrument type. All images are placed automatically according to stage position coordinates when stored in the image files. Otherwise, the Grid Layout Wizard helps to lay out images in seconds. topoStitch™ even offers advanced snapping and semi transparent rendering, which makes it easy to place and adjust images manually.
