Filter Results By:
Products
Applications
Manufacturers
RS422
One of several standards that incorporate balanced line signals into DB connectors. A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines. (www.sangoma.com)
See Also: Serial Communications, I2C, RS232, RS485
- TEAM SOLUTIONS, INC.
-
product
RS-485/RS-422
Renesas' half duplex and full duplex RS-485/RS-422 transceivers are available in a variety of speed grades to address any application needing reliable data transmission over twisted pair wiring.
-
product
USB⇔RS-422/RS-485
SI-35USB
SI-35USB is an USB converter, which converts USB of PC into RS-422/RS-485.
-
product
Interface RS-485 and RS-422
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
product
RS-485 and RS-422 Transceivers
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
product
RS-485, RS-422 & RS-232
Renesas has a rich interface history dating back to the 1970s. Our RS-485, RS-422 and RS-232 transceivers are used by the biggest names in industrial process control, telecommunications, and hundreds of different applications.
-
product
RS-422 RS-423 RS-485
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
- RS-232 to RS-422/RS-485 Converter
Model 285
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
- RS-422 Opto Isolation Module
Model 8381
FEATURES: Opto Isolation; Built-in Power Supply; 115.2 KBPS Data Rate; DIN Rail Mounted; Full Duplex; Programmable Terminations. The Model 8381 RS-422 Opto Isolator allows re-generating and extending the distance of RS-422 networks while maintaining optical isolation between the ports. Model 8381 allows for the extension of RS-422 links to a maximum limit of 3,300 feet or 1 km at any data rate up to 115 KBPS.
-
product
USB⇔RS-422/RS-485 Conversion
SI-35USB-2
SI-35USB-2 is an USB converter, which converts USB of PC into RS-422/RS-485.
-
product
- RS-422 to Fiber Optic Converter
Model 272A
FEATURES: Data Rate to 2.5 MBPS; Full Duplex TD and RD; ST Connectors; Extends RS-422 Network up to 2 km (6,600 ft). The Model 272A provides the capability of performing an interface conversion between full duplex, RS-422 signals and their equivalent for fiber optic transmission.
-
product
LAN⇔RS-422/RS-485 Conversion
SI-65A
SI-65A is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
product
LAN⇔RS-422/RS-485 Conversion
SI-65
SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
product
RS-485/RS-422 Fault Protected
Renesas' fault protected RS-485/RS-422 transceivers, also known as overvoltage protected transceivers (OVP), offer robust fault tolerance and high performance.
-
product
4-Port RS232/4-port RS422
3101
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTS, with four ports using RS232 signal levels, and four ports using RS422 signal levels. The four RS232 ports each provide the full set of data and modem control lines configured for DTE
-
product
RS-232 to RS-422 Interface Converter
Model 63-2SA
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
product
- RS-422 and RS-485 Lightning/Surge Protector
Model 22NX
FEATURES: Triple Stage Protection; Fast Response Time For RS-422 / RS-485; Prevents Damage to Modems, Converters, and Terminals; Accommodates Data Rates to 10 MBPS; Supports 4 Circuits. The Model 22NX Lightning Sponge is designed to accommodate high-voltage transients, slow them down and redirect them to a low impedance path to earth ground.
-
product
- RS-232 to RS-422 Interface Converter
Model 263
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
RS-232 to RS-422 Interface Converter
Model 253
FEATURES: DB9 Data Port; Compatible with PC/386/486; Full Duplex; Surge Protection. Adding an RS-422 interface to a PC is now a snap. The Model 253 Interface Converter does this for full duplex signals at data rates up to 19.2 KBPS, without requiring any AC or DC power. With only TD, RD and ground, the Model 253 provides operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
RS-232 to RS-422/RS-485 Converter
ND-6520
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
USB to RS-422/RS-485 Converter
ND-6530
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
RS422 Mode SI-module With Optical Isolation
MX422-G
RS422 mode SI-module with optical isolation
-
product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
RS-232 to RS-422/RS-485 Interface Converter
Model 9365
FEATURES: DIN Rail Mountable; User Selectable RS-422 or RS-485; User Selectable Two- or Four-wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 kbp.
-
product
RS-422/485 Serial Communication Card
LPCI-COM-1S
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
product
RS-422/485 Serial Communication Card
PCI-COM-1S
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
RS422 mode SI-module with optical isolation and RTS/CTS
-
product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
product
GPIB-RS485/RS422 GPIB Instrument Control Device
779733-02
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488, RS485, and RS422 standards, as well as interpret and execute high-level commands from the serial port, including serial‑to‑GPIB, and GPIB‑to‑serial protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
