Filter Results By:
Products
Applications
Manufacturers
RS232
A standard interface for serial binary data interchange defining voltage levels for logical one and logical zero, standard transmission speed and connector types.
See Also: Serial Communications, I2C, RS422, RS485
- Pickering Interfaces Inc.
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
RS-232
The RS-232 family includes transceivers with auto-power-down and standby functions, multi-channel interfaces and driver/receiver circuits. These devices have a 5 V supply or a 3 V to 5 V supply and are ESD protected enabling true RS-232 performance.
-
product
RS-232
Renesas' RS-232 transceivers are available in many configurations and feature data rates up to 1Mbps, IEC61000 ESD protection, low power shut down modes, and small QFN packages.
-
product
Interface RS-232
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
product
Isolated RS-232
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
-
product
TTL to RS232 Adapter
SKU-012-XX
The TTL to RS-232 adapter connects the Serial UART to the standard RS-232 port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
product
RS232 to RS485-RS422 Converter
Shenzhen Sintech Electronic, Inc.
RS232 TO RS485-RS422 CONVERTERFull range of data communication products,RS232 to RS485,RS232 to RS485/422 converter,it is widely used in field:Point to point, point to multi-point communication; Industrial distribution system, industrial control automation; Road traffic control automation; Closed circuit monitoring; Security protection system; Intelligent card, check on work attendance gate safety system.
-
product
RS232 to DMX Converter
DS232
RS232 to DMX Converter Controller Driver. Connect an RS232 terminal or computer port and drive DMX controlled dimmers and devices. A set of commands and auto fade rates offer power and flexibility for controlling DMX equipment. Use any RS232 terminal application to create command strings to: turn on, off, fade up, and fade down dimmer 256 DMX channels.
-
product
Transducer with RS232 Interface
RS232 transducers / transmitters for temperature, humidity, atmospheric pressure and CO2.
-
product
RS-485, RS-422 & RS-232
Renesas has a rich interface history dating back to the 1970s. Our RS-485, RS-422 and RS-232 transceivers are used by the biggest names in industrial process control, telecommunications, and hundreds of different applications.
-
product
RS-232/RS-485 Converter
ECD485
Deploy sub-metering sites and simple metering networks with ease using the EDMI MiniHub RS-232 to RS-485 converter.1/4 Load RS-485 modules allow for up to 128 devices over 1.2km of wired daisy-chain network, with each meter capable of becoming the Network Master and remotely connecting to a backhaul system via an integrated EDMI Modem Port redirect connector.
-
product
RS-232 and RS-562 Transceivers
Analog Devices offers single, dual, and combination transceivers of up to five RS-232/RS-562 drivers and receivers for 1.8 V to 5.5 V power supplies. Data terminal equipment (DTE) or data communications equipment (DCE) configurations are also available in 3.3 V or 5 V versions. Galvanically isolated modules break ground loops and provide a convenient, self-powered, isolated, low EMI solution that drastically reduces component count and design complexity.
-
product
RS232 I2C Adapter
12C Master
*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
RS-232 to RS-422 Interface Converter
Model 63-2SA
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
product
- RS-232 to RS-422/RS-485 Converter
Model 285
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
RS-232 Passive Tap Module
EZ-TAP™
Stratus Engineering’s EZ-Tap hardware module is a low-cost hardware bus analyzer and protocol analyzer solution that uses a traditional dual COM port approach to RS232 interface monitoring.
-
product
Datalogging Light Meter (RS-232)
DLM 536
Spectrum of photo sensor meets C.I.E. photopic curve V(l). 16000 Records Data logging capacity. RS-232 interface (software included). Measurement of luminous intensity(PC Software)
-
product
- RS-232 to RS-422 Interface Converter
Model 263
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
- RS-232 to Current Loop Converter
Model 65A
FEATURES: Active/Passive Loops; 20 or 60 mA. Operation; DC To 19.2 KBPS; Half/Full Duplex; Optically Isolated; DTE/DCE Selectable. The Model 65A is a small, versatile, RS-232 to Current Loop Converters for use with teletypes or computers providing local terminal input via a 20mA. (or 60 ma.) current loop. The Model 65 includes a wall mounted transformer and internal power supply circuitry.
-
product
RS-232 to EIA-530 Interface Converter
Model 62-1 / 62-2
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
product
RS-232 to RS-422/RS-485 Converter
ND-6520
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Computer Interface, GPIB and RS-232
SR245
Stanford Research Systems, Inc.
The SR245 Computer Interface module is a powerful tool for data acquisition. It provides both an analog and a digital interface between your computer and your experiment.
-
product
Four Port RS-232 Interface
PCI-COM232/4
Serial ports: 4Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with fanout cable to 4 DB-9 or DB-25 male connectorsPower: +5V only
-
product
pH/ORP handheld meter with RS232
CyberScan pH 110
5-point Push-Button Calibration with Auto-Buffer Recognition for quick calibration with no calibration mistakes
-
product
Precision DMM with RS232 Interface
HH2215
Resistance test up to 40MΩ. Wide Frequency test range from 10Hz to 300kHz. Capacitance measurement up to 100uF. Temperature test range from -4oF to 572oF to 300oC. Diode test audible continuity check and Transistor test
-
product
- RS-232 DB9 Lightning Suppressor
Model 29
FEATURES: PC 386/486 Pentium Com Ports; Nanosecond Response; DB9 Connectors; Protects All 9 Lines; Ground Stud & Wire Included. The Model 29 contains avalanche diodes, one for each line. All diodes are returned to a ground stud. The Model 29 is provided with a 2-foot ground wire and has male and female DB9 connectors.
-
product
- RS-232 Opto Isolation Module
Model 268
FEATURES: Total Electrical Isolation; Eliminates Noise Problems; Eliminates Ground Loops; Use for Data & Control; UL Components. The Model 268 Opto Isolation Module provides a communications link that has no electrical connections from one port to the other.
-
product
Single Port RS-232 Interface
PCI-COM232
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
product
10KHz / RS232 LCR Meter
MCH-8817A
Features:*Multiple functions with easy operation *Big white back-light LCD display*6 typical test frequencies *3 typical test levels: 0.1V, 0.3V and 1.0V*2 selectable output impedances: 30Ω and 100Ω
-
product
Bench pH/mV RS232 Meter
CyberScan pH 1100
High Resolution and Accuracy (Up to ±0.002 pH Accuracy) for precise measurementBacklit Two Line, Dot Matrix LCD Display provides clear instructions for setup, measurement and calibration
