Filter Results By:
Products
Applications
Manufacturers
Time Delay Relays
Time difference between two events. (thefreedictionary.com)
- Pickering Interfaces Inc.
product
PXI Dual 4 to 1 RF MUX SMB 75 Ohm
40-832-002
The 40-832-002 is a 75 Ohm 4 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-832 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
Time Delay Relays
DARE Electronics manufactures a wide variety of time delay relays including fixed and adjustable delay on operate and delay on release time delay relays, repeat cycle timers, interval timers, and motor driven timers. Time Delay Relays can be used in a various applications, such as event sequencing, instrument control, alarm circuits, or watchdog circuits.
-
product
High Current 45 Relay PXI Card
GX6315 Series
The GX6315 is a 45 channel, high current relay board that plugs directly into any 6U PXI slot. The GX6315 also provides nine transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
product
Multi Function Relay PXI Card
GX6377
The GX6377 3U PXI multi function switch card provides users with the ability to switch both high current and general-purpose signals using only one 3U PXI switch module. The card features multiple channels of high current switching capability for 10 A and 2 A applications as well as two, 16 x 2 switch matrix groups, which can also be configured as a 32 x 2 or 16 x 4 matrix.
-
product
High Current Relay PXI Card
GX6115
The GX6115 is a 15 channel, high current relay board that plugs directly into any 3U PXI slot. The GX6115 also provides three transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
General Purpose Switching PXI Card
GX6325
The GX6325 is 6U switching card with 75 SPDT Form C relays with a switching power rating of 60 W. Featuring the highest density available in PXI for this type of switch card, the GX6325 is suitable for all test applications requiring general purpose, low level switching.
-
product
PXIe-2542, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module
780587-42
PXIe, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module - The PXIe‑2542 is a terminated switch module suited for routing RF signals for production test applications. It features high-performance solid-state relays that offer unique benefits such as unlimited mechanical lifetime and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel. The channel termination and COM lines help minimize reflections of the RF signal and protect your instruments.
-
product
PXI-2586, 10-Channel, 12 A, SPST PXI Relay Module
778572-86
10-Channel, 12 A, SPST PXI Relay Module—The PXI‑2586 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay has low contact resistance and high isolation voltage. The PXI‑2586 is fully software programmable. It is rated for both high currents and high voltages, so it is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing.
-
product
PXIe-2569, 100-Channel, 1 A, SPST PXI Relay Module
780587-69
PXIe, 100-Channel, 1 A, SPST PXI Relay Module—The PXIe‑2569 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It is fully software programmable and contains a 32,000‑step scan list for deterministic scanning capability. This module offers maximum relay density, so it is ideal for medium-power automated test loads.
-
product
PXI-2799, 40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
782359-01
40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2799 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2799 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2569 , 31-Channel, 2 A, SPST PXI Relay Module
778572-69
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2569 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It is fully software programmable and contains a 32,000‑step scan list for deterministic scanning capability. This module offers maximum relay density, so it is ideal for medium-power automated test loads.
-
product
PXI-2542, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module
778572-42
6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module - The PXI‑2542 is a terminated switch module suited for routing RF signals for production test applications. It features high-performance solid-state relays that offer unique benefits such as unlimited mechanical lifetime and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel. The channel termination and COM lines help minimize reflections of the RF signal and protect your instruments.
-
product
PXI-2599, 26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
778572-99
26.5 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2599 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2599 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2548, 2.7 GHz, 50 Ω, Quad SPDT PXI RF Relay Module
778572-48
2.7 GHz, 50 Ω, Quad SPDT PXI RF Relay Module - The PXI‑2548 is a general-purpose single‑pole double‑throw (SPDT) switch module. You can use it to add flexibility to your switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2549, 2.7 GHz, 50 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-49
2.7 GHz, 50 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2549 is a general-purpose single‑pole double‑throw (SPDT) switch module. You can use it to add flexibility to your switch network or to maintain uniform signal paths across multiple channels when building high‑channel‑count multiplexers. The PXI‑2549 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
product
PCI-6520, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (60 V), Isolated Digital I/O Device
779443-01
The PCI-6520 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. For added safety the PCI-6520 requires a keyed connector. If a computer or application fault occurs, the PCI-6520 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
product
PXI-2570 , 40-Channel, 1 A, SPDT PXI Relay Module
778572-70
40-Channel, 1 A, SPDT PXI Relay Module—The PXI‑2570 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
product
PXI-2559, 2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module
778572-59
2.5 GHz, 75 Ω, Dual-Terminated SPDT PXI RF Relay Module - The PXI‑2559 is a general-purpose switch module featuring two independently terminated single‑pole double‑throw (SPDT) relays. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high-channel-count multiplexers. The PXI‑2559 termination resistors minimize reflections on open channels and protect your source or device under test from damage. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI-2521, 40-Channel, 2 A, DPST PXI Relay Module
778572-21
40-Channel, 2 A, DPST PXI Relay Module—The PXI‑2521 is a general-purpose switch module that features independent double‑pole single‑throw (DPST) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2521 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI-2522, 53-Channel, 2 A, SPDT PXI Relay Module
778572-22
53-Channel, 2 A, SPDT PXI Relay Module - The PXI‑2522 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2522 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI-2568, 31-Channel, 2 A, SPST PXI Relay Module
778572-68
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2568 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2568 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI-2571, 66-Channel, 1 A, SPDT PXI Relay Module
778572-71
66-Channel, 1 A, SPDT PXI Relay Module—The PXI‑2571 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
product
PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module
778572-20
80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI-2523, 26-Channel, 2 A, DPDT PXI Relay Module
778572-23
26-Channel, 2 A, DPDT PXI Relay Module - The PXI‑2523 is a general-purpose switch module that features independent double‑pole double‑throw (DPDT) armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2523 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
product
PXI-2558, 2.5 GHz, 75 Ω, Quad SPDT PXI RF Relay Module
778572-58
2.5 GHz, 75 Ω, Quad SPDT PXI RF Relay Module - The PXI‑2558 is a general-purpose single‑pole double‑throw (SPDT) switch module. You can use it to add flexibility to your video switch network or to maintain uniform signal paths across multiple channels when building high‑channel‑count multiplexers. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
CPCI-Relay32
CPCI-Relay-32
CPCI Bus Interface 3.3 / 5 Volt PLX 9056 66MHz 32-bit, PCI r2.2compliant
-
product
8-CH Relay Outputs & 8-CH Isolated DI Card
LPCIe-7250
LPCIe-7250 provides 8-CH SPDT (Form C) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are non-polarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments.
-
product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
product
PXI Switch - 16-CH General-Purpose SPDT Relay Module
PXI-7901
ADLINK PXI-7901 is a general-purpose (GP) switch module implementing 16-CH independent single-pole double-throw (SPDT) relays (1 Form C). PXI-7901 can connect one input to one output and be used as signal switching and routing for measurement system or ATE. Thanks to its high switching capacity, PXI-7901 can also be used to turn on or turn off devices such as motors, fans, heaters, and lights. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7901, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
