- Pickering Interfaces Inc.
product
PXI 8 Slot BRIC Module, 2 Resource Distributor, 2 Bus Matrix Inputs
40-569B-122
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-122 is a 8 slot module fitted with 2 Bus Matrix Inputs cards and 2 Resource Distributor cards.
-
product
I2C Bus Host Adapters
iPort/AFM 2 brings I2C directly to your Windows, Linux, or Mac OSX PC, Single-board Computers, or Embedded Systems. Just load our free software, plug the iPort/AFM 2 into your computer's legacy or add-on RS-232 port, and you will be sending and receiving I2C Bus messages in minutes.
-
-
product
PCI bus Test Adapter
pcibus1b
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
product
PCI to PC/104+ Bus Adapter
327/328
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
product
Carrier Cards and Bus Adapters
Abaco's wide range of carrier cards allows you to expand your systems capabilities simply and cost-effectively, allowing easier technology insertion.
-
product
Adapter
EXC-1553UNET/Px(S)
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units c...show more -
product
Interface Adapter
DMX-10
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
product
USB Adapters
DekTec's classic and iconic portable adapters for USB bus are well known tools in the industry. Some of them can be considered essential tools for every DTV engineer! DekTec is proud that it has won prestigious awards at NAB and IBC for several of its USB adapters.
-
product
PCI-104 Adapter for PMC
PC104p2PMC
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
-
product
PCI Adapter for cPCI
PCI2cPCI-32
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
PMC to PCI Adapters
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
product
USB to I2C Adapter
Model JI-300
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
product
Osprey ISA Unibus Adapter
9476-U-B
Unibus Controller board is EISA/ISA bus compatible and occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
product
PCI to PCI Express Adapter
SKU-011-01
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
-
product
cPCI to PMC Adapter / Carrier
cPCI2PMC
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
product
cPCI to PMC Adapter / Carrier
cPCIBPMC
The cPCIBPMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCIBPMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
product
Flexible MiniPCI to PCI Adapter
SKU-036-01
The Flexible MiniPCI to PCI Bus Adapter (Adapter) was designed to expand a modern motherboard (ATX, mini ATX, etc.) with a limited number of PCI connectors. The Adapter allows you to connect up to two 32-bit PCI add-in boards to the motherboard’s MiniPCI connector.The Adapter includes a PCI adapter, MiniPCI host board and a PCI Express flat cable.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Osprey ISA Q-Bus Adapter board
9476-Q-B
Qbus Controller board for Osprey ISA/EISA bus compatible. Occupies PC slot adjacent to item 2 or 3. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
PMC to PCI Adapter for test and development
8091
The PMC-to-PCI Adapter for Test is an active extender that accommodates live insertion of one PCI Mezzanine Card (PMC) for performance analysis and testing in a PCI bus environment.
-
product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
product
Flexible MiniPCI to MiniPCI Express Adapter
SKU-054-0X
The Flexible MiniPCI to MiniPCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a MiniPCI Express bus. It allows you to connect a MiniPCI Express board (half-size or full-size) to a motherboard that has a standard 124-pin MiniPCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), MiniPCI host board and PCI Express flat cable.
-
product
Flexible MiniPCI to PCI Express Adapter
SKU-037-XX
The Flexible MiniPCI to PCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a PCI Express bus. It allows you to connect a x1 PCI Express add-in board to a motherboard that has a standard 124-pin MiniPCI connector.The adapter includes a MiniPCI host board, x1 PCIe (x4 PCIe is optional) adapter board and a PCI Express flat cable.
-
product
LXI WTB Adaptor, Thru line
60-982-001
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple ...show more -
product
Flexible 32-bit PCI to MiniPCI Express Adapter
SKU-057-0X
The Flexible 32-bit PCI to MiniPCI Express Adapter (Adapter) was designed to convert the 32-bit PCI bus into a MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion board to the motherboard PCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), 32-bit PCI host board and PCI Express flat cable.
-
product
Flexible Mini PCI Express to MiniPCI Adapter
SKU-066-0X
Flexible MiniPCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert motherboard MiniPCI Express bus into a standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard’s MiniPCI Express connector via full- or half-size MiniPCI Express host board.Adapter includes MiniPCI Adapter board, MiniPCI Express host board and flat PCI Express Cable.
-
product
Flexible MiniPCI Express to PCI Express Adapter
SKU-035-XX
The Flexible MiniPCI Express to x1, x4 or x16 PCI Express Adapter (Adapter) was designed to convert the MiniPCI Express bus into x1, x4 or x16Express bus and extend it. It allows you to connect a x1, x4 or x16 Express expansion add-in board to the motherboard’s MiniPCI Express connector.The Adapter includes an x1, x4 or x16 PCI Express adapter board, MiniPCI Express host board (full-size or half-size) and a PCI Express flat Cable.
-
product
Flexible x1 PCI Express to MiniPCI Adapter
SKU-067-0X
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
