Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Frequency Response Analyzer
A frequency response analyzer measures the gain and phase response characteristics with respect to frequency of the device or system under test, by applying a frequency swept sine wave to it and examining its response signal.Featured wide dynamic range realizes high precise measurement, and also ultra low frequency measurement.
-
product
Frequency Response Analyzer
1250E
The 1250E Frequency Response Analyzer (FRA) delivers accurate measurement of gain and phase. The device under test is stimulated by a sinewave and the response analyzed at various points in the system. These responses are then correlated with the stimulus to determine the amplitude and phase relative to the generator. The ratio of the two measured signals can then be used to provide the system transfer function.
-
product
Frequency Response Function
FRF
FFT Spectral Analysis. Frequency Response Function (FRF) is a commonly used measurement type of the Dynamic Signal Analyzer. FRF is defined as the ratio of response i.e. acceleration, velocity, or displacement with respect to the excitation force which is the reference.
-
product
Frequency Response Analyzers
The PSM range of instrumentation provide not just conventional frequency response measurements but can also be combined with an Impedance Analysis Interface to form a high accuracy impedance analyser, in the case of the PSM3750 this solution is able to provide impedance analysis up to 50MHz
-
product
Frequency Response Analyzers
Venable Instruments has been focused on one goal: bringing the most versatile, full-featured frequency response analyzers to customers in industries where precise testing and measurement tools for power supply design is critical. Over 37 years of continual research and development has created the widest range of scalable frequency response analyzers to meet your company's current requirements, while providing a cost-effective growth path for increased testing functionality. Venable is a proven leader in aerospace, automotive, energy, defense, computer technology, academia, government research applications and virtually any industry requiring the highest standards in power supply and stability testing for repeatable and accurate results.
-
product
Frequency Response Analyser
DP-cPCI-7554
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
product
Frequency Response Analyzer
1253A
The 1253A Frequency Response Analyzer (FRA) is an instrument that is capable of meeting today's measurement requirements for dynamic system analysis. Using the Single Sine Correlation technique (SSC), it provides precise data relating to the gain and phase between any points in a dynamic system. This instrument enables engineers to perform searching analysis to assess performance of both simple or complex systems.
-
product
Impulse Response Measurements
Dirac
Dirac is a sophisticated tool to calculate a very wide range of acoustical parameters from impulse response measurements of an enclosure. Through many years of development and customer feedback, Dirac has grown to support many different applications. Due to its user friendly interface it is suitable for field measurements, but it also contains many advanced features that make it useful in a laboratory or research setting.
-
product
Frequency Response Analyzers
350C Series
Venable Model 350c is the 3 channel successor to the original workhorse Model 350a/b that launched in 1986 and established Venable Instruments as a market leader. The contemporary 350c Series incorporates a 3rd channel, allowing the user to measure more transfer functions simultaneously with one sweep, such as source and load impedance. The 350c is the only frequency response analyzer in the industry that can measure absolute phase, using a reference channel.
-
product
Frequency Response Analyzers
Frequency Response Analysis (also referred to as Transfer Function Analysis) measures the output spectrum of a system relative to a stimulus, and is used to characterize the dynamics of the system under test. The technique measures the magnitude and phase relationship between output and input waveforms as a function of frequency. The input signals may be from a wide range of sensors including acoustic (microphones/sonar), mechanical (accelerometers/displacement transducers), optical (photodetectors), and electrical (amplifiers).
-
product
Frequency Response Analyzer
CAPture FRA
A Frequency Response Analyzer (FRA) is a high precision measurement instrument used to analyse dynamic behavior of circuits & components of control systems in the frequency domain. An FRA generates a sinusoidal signal and inserted it into a unit under test. This signal is measured at the point of insertion using one of the input channels on the FRA The inserted signal travels through the UUT and the same signal is measured simultaneously by the FRA at other input channel. The technique measures the magnitude and phase relationship between output and input waveform as a function of frequency.
-
product
Frequency Response Analyzers
Sleuth RA-Series
The Sleuth RA-Series is at home in any environment as well. It's 1-U high form factor, allows for compact desktop use or, it can be mounted in a rack with optional brackets. When attached to a modest user provided Windows PC (desktop or laptop), it becomes a powerful ally in your toughest design, test or trouble-shooting requirement.
-
product
Frequency Response Analyzers
7400 Series
The Venable Model 7400 Series is the top of the line in Venable performance, supplying 4 channels for increased testing, measurement and analysis functionality. Originally designed for measuring 3-phase impedance and source and load simultaneously, the Model 7400 is a robust solution for organizations requiring high availability for high volume and/or simultaneous testing.
-
product
Frequency Response Analyzers
6300 Series
The Venable Model 6300 Series is our popular 2-channel hardware/software system supplying the same functionality as all Venable FRAs, with the 6300 leading the industry with more integrated testing and measurement capabilities than any other instrument in its class.
-
product
Frequency Response Analyzer
1255B
Using the single sine technique the 1255B provides precise measurement of gain and phase between any two points in a system. This fully digital technique is used to assess the performance of both simple and complex systems - electrochemical, materials, electronics, mechanical, and acoustic.
-
product
Shock Response Spectrum Analysis
A Shock Response Spectrum (SRS) is a graphical presentation of a transient acceleration pulse’s potential to damage a structure. It plots the peak acceleration responses of a bank of single degree-of-freedom (SDOF) spring, mass damper systems all experiencing the same base-excitation as if on a rigid massless base. Each SDOF system has a different natural frequency; they all have the same viscous damping factor. A spectrum results from plotting the peak accelerations (vertically) against the natural frequencies (horizontally).
-
product
Fast Response Gas Detector
Leaksurveyor
Teledyne Gas & Flame Detection
The GMI Leaksurveyor combines quality, ruggedness and advanced Technology in a user friendly, portable gas detector. The integral fast response and high sensitivity semiconductor sensor enables leakage surveys to be performed and distribution leaks to be quickly found.
-
product
Sweep Frequency Response Analyzer
FRANEO 800
FRANEO 800 was developed for testing the mechanical and electrical integrity of power transformers after transportation or exposure to high fault currents. It uses the sweep frequency response analysis (SFRA) principle and measures the electrical transfer function over a wide range of frequencies.
-
product
MEMS DC Response Accelerometers
PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.
-
product
Sweep Frequency Response Analyzer
M5400
The M5400 sends an excitation signal into the transformer and measures the returning signals. Comparing this response to baseline readings and results from similar units allows you to identify deviations and confirm internal mechanical problems.The M5400 reduces the uncertainty about apparatus condition by providing solid evidence of mechanical integrity or winding movement. Use it to help determine how a transformer is deteriorating, if it can go back in service after a fault or if it has been damaged during transit.
-
product
Digital/Analog Frequency Response Analyzer
8800 Series
The analyzer utilizes a digital “Sync” signal to provide synchronization between analog and digital hardware. The Model 8800 performs simultaneous analysis on both analog input channels and digital target processor, reliably capturing all data. Versatile by design, the Model 8800 digital interface can be disabled, via software, to use the analyzer in a standard 2-channel, analog-only configuration.
-
product
Pyranometer Verified Cosine Response
CMP 21
The CMP 21 pyranometer is designed for measuring the irradiance (radiant flux, Watt/m) on a plane surface, which results from the direct solar radiation and from the diffuse radiation incident from the hemisphere above.
-
product
Impedance Analyser Frequency Response Analyser
C60
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
product
Spectral Response (Spectral Sensitivity) Measurement
It is used to measure the spectral response (spectral sensitivity) of photoelectric conversion devices (photodetectors / sensors) such as silicon photodiodes and CCD · CMOS image sensors . Measurement in the broadband wavelength region can be performed with low stray light.
-
product
Global Network Monitoring and Incident Response
NetOmni™
NIKSUN NetOmni™ collects information (e.g., Logs, NetFlow, SNMP, Packets, etc) from all network applications, services, and their underlying infrastructure and prioritizes key service delivery, security, and compliance metrics. This enables powerful correlated dashboards and workflows from a single pane of glass.
-
product
Digital Stimulus Response PXI Card
GX5152 Series
The GX5152 Series are high speed, 6U PXI, digital I/O instruments. The GX5152 master controller has 32 I/O channels that supports test rates up to 50 MHz and vector depths up to 128 Mb per pin. The GX5153 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5152. The GX5152 can control up to 15 GX5153 boards using the same timing and sequencer.
-
product
Digital Stimulus Response PXI Card
GX5152
The GX5152 Series are high speed, 6U PXI, digital I/O instruments. The GX5152 master controller has 32 I/O channels that supports test rates up to 50 MHz and vector depths up to 128 Mb per pin. The GX5153 slave offers the same timing characteristics and multiple I/O level configurations when used in conjunction with the GX5152. The GX5152 can control up to 15 GX5153 boards using the same timing and sequencer.
-
product
Indoor Gunshot Detection And Response System
Pre-SenseShot
Information System Technologies Inc.
ISTI offers a new detection system to the facility security and safety industry to quickly neutralize an active shooter and more quickly secure and protect occupants. When confronted with an active shooter situation first responders and safety personnel face immediate tactical disadvantages. Beyond rushing towards ensuing chaos, 9-1-1 calls and eye witness reports are often disjointed, inaccurate, and lack precise location information required to make real time responsive decisions as they arrive on scene. Likewise within the building, the crisis triggers panic and chaotic scrambles towards exits and assumed safe havens. However unorganized and uniformed retreats may actually be leading evacuees back into harm’s way.
-
product
Shock Response Spectrum (SRS) Analysis Solution
Shock Response Spectrum (SRS) Analysis SolutionMechanical shock pulses are often analyzed in terms of the shock response spectrum. The shock response spectrum assumes that the shock pulse is applied as a base input to an array of independent single-degree-of-freedom systems. SDOF system assumes that each system hat its own natural frequency.
-
product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions. .The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
