- Applied Instruments, Inc.
product
Satellite Signal Level Meter
Super Buddy
Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their individual transponders. The Super Buddy even gives the elevation and azimuth for whichever satellite you select.
-
product
ID Bundle
Cost effective bundle of eVision's identification librariesIncludes EasyImage, EasyOCR, EasyOCR2, EasyBarCode, EasyMatrixCode and EasyQRCode
-
product
ID Reader 8
ID Reader 8″ is the best tool to avoid lot errors. Designed for using 200mm – 8″ notch aligner and OCR system, it checks your carrier tag, reads each wafer scribes, then sends the information to your Host with SECSII Gem commands
-
product
Phase ID Systems
LED Meter Probe allows the user to take Real time Phase Angle readings along with AC nominal voltage readings. A PD800W LED Meter Probe works in conjunction with the Receive Unit to verify phase identification along with the actual phase angle data. This is all done without any calculations or data transfer from the field to a base computer. The meter probe and reference probe or receive unit can operate at 100 feet of separation and up to 300 feet line of sight separation. In the event that this distance would need to be greater, the Receive Unit can be unplugged from the charging cable and taken into the field while operating on it's rechargeable batteries for up to 8 hours at a time.
-
product
Banking, ID & Transport
ST’s secure microcontrollers are designed for a wide range of applications including SDA & DDA banking, identification, transport and Pay TV solutions. From traditional smart cards to innovative wearables and biometric solutions, ST offers a complete portfolio of contact, dual-interface and contactless secure microcontrollers.
-
product
Fault ID & Repair
As a manufacturer of bare PCBs, you know that your reputation sits right on top of every board you send out. You have to get them right, but with every PCB you discard, you’re throwing away precious labor, materials, power and time, along with many other costly elements that go to make up your products. That’s why it’s important to know which of your flagged boards are in fact electrically sound, and whether repair is a viable, reliable option.
-
-
product
1/8" ID Contacts
VPC offers a range of pneumatic contacts that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
-
product
3/8" ID Contacts
VPC offers a range of pneumatic connectors that are ideal for use with automatic engagement interface systems. These pneumatic contacts also work well when used together with the VPC iDock Series.
-
product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
-
product
Inside Dimension (ID) Measuring Instruments
Pratt & Whitney Measurement Systems, Inc.
High accuracy is maintained by its laser interferometer, zero Abbe offset design, and large measuring table with swivel, center, tilt, and elevation control knobs.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the...show more -
-
-
-
product
Production Caller ID Signal Simulator
AI-80
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
-
-
-
-
-
product
ID, CASS, 19 Module, Single Tier, Commercial
410113105
ID, CASS, 19 Module, Single Tier, Commercial.
-
product
ID, CASS, 19 Module, Single Tier, Extended
410113111
ID, CASS, 19 Module, Single Tier, Extended.
-
product
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
510104160
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
-
product
Signal, Module, ID, CASS, 210 Position, P4
510114122
Signal, Module, ID, CASS, 210 Position, P4.
-
product
Signal, Module, ID, CASS, QuadraPaddle, 800 Position
510114131
Signal, Module, ID, CASS, QuadraPaddle, 800 Position.Mating module is 510113138.
-
product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
product
Signal, Module, ID, CASS, 64 Position, Discrete Wiring
510114108
Signal, Module, ID, CASS, 64 Position, Discrete Wiring.
-
product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
product
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
510114109
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
