Filter Results By:
Products
Applications
Manufacturers
-
product
Conducted Emission
AFJ FFT 3010 & 3030 EMI Receivers have been especially designed for conducted emission measurement, both during EUT diagnostic development and for final compliance testing.
-
product
Conducted Emissions Analyzer
CE Analyst™
With CE Analyst circuits can be analyzed prior to fabrication to determine whether conducted emissions requirements will be satisfied. CE Analyst is ideally suited to predicting conducted emissions for a variety of circuit applications.
-
product
RF Shielded Chamber
MIL-STD
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
product
EMC Testing Services
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
product
Emergency Conditions Testing
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Comb Generator
CG 50/500
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
product
EMC Testing Knowledge & Equipment
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
product
Radiated Emissions Analyzer
RE Analyst™
RE Analyst uses the conducted emissions output data produced by CE Analyst as its input. Radiated emissions are calculated using Method of Moment techniques.
-
product
IC Measurement Technology
Emission
is used to measure conducted emissions (measurements with direct 1 Ohm/150 Ohm-coupling) according to IEC 61967-4 at IC pins.
-
product
Ancillaries.. Conducted
The ease and effectiveness of conducted emission measurements can be enhanced by the use of appropriate filters. In particular, broadband noise below the frequencies of interest can cause limiting (compression) in spectrum analysers, distorting the measurements.
-
product
9 kHz Highpass Filter
TBHPF1-9KHZ
9 kHz Highpass Filter for protection of spectrum analyzer or EMI-receiver RF inputs against high amplitude subharmonics and residual 50 Hz voltage in conducted emission measurement set ups
-
product
3GHz EMC emissions Analyser
SA3000
The SA3000 is a powerful, fully featured, EMC analyser. It will measure both conducted and radiated emissions according to the international EMC standards. It enables the user to assess the EMC compliance of products quickly and with good integrity.
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
Near Field Probes
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
product
Comb Generator
CG01
The main application of Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble shooting Open Area Test Sites(OATS).An OATS must be completely calibrated before it is put into service. reference signal source Noise Generators Signal Generators
-
product
1GHz EMC Emissions Analyser
SA1002
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
product
Line Impedance Stabilization Networks
LISN
LISN stands for 'Line Impedance Stabilization Network'. Com-Power offers a line of LISNs developed for conducted emission testing according to the most commonly adopted EMC specifications like CISPR, FCC, ISO, EN, RTCA DO-160 and MIL-STD 461D. The LISN circuit is designed and constructed to meet the performance criteria given by these standards.
-
product
EMC Accessories
Complete your EMC test setup with the essential accessories to compliment the test equipment. Whether it is a LISN (or V-Network) to counteract interference from external power sources on conducted emissions from the device under test, probes to locate the near field sources of radiated emissions, receive and transmit antennas, or tripods for holding antennas in place, the Rohde & Schwarz catalog of EMC accessories provides the additional items you need for EMI and EMS measurements, guaranteed 100% suitable for use with Rohde & Schwarz EMC test equipment.
-
product
CARB Testing
Underwriters Laboratories Inc.
The ASTM D6007 (small chamber) and ASTM E1333 (large chamber) test methods are used by the composite wood products industry to measure emissions of formaldehyde from plywood, particle board and medium-density fiberboard (MDF), commonly known as CARB testing. Testing is conducted in environmental chambers operated at defined product loading, temperature and relative humidity.
-
product
General Purpose L-Chassis Single Output Power Supplies
Series RTW
Kepco's RTW series are general-purpose, L-chassis, single output power supplies.They are available in 50, 100, 150 and 300-watt power levels. Their small size and very low profile allow the RTW to be fitted into small spaces. They feature full safety compliance to international standards and have suppressed both conducted and radiated emission to FCC class B levels.
-
product
Transient Limiters
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
product
300W Generap Purpose U-Chassis Single-Output Power Supplies
Series RMW
Kepco's RMW series are 300-watt general-purpose, U-chassis, single output power supplies, with model RMW 51212K-300 offering a triple output: +5V and ±12V.Their small size and very low profile allow the RMW to be fitted into small spaces. They feature full safety compliance to international standards and have suppressed both conducted and radiated emission to FCC class B levels.
-
product
Emissions Test System
PC-114
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
product
EMC Testing
Keystone Compliance is a unique EMC test facility because of our focus on assisting our customers achieve the measurements and certifications that they are seeking. Our lab features three 3-meter EMC chambers and two military/aerospace EMC chambers. In addition to the chambers, the lab significant ground planes, equipment and software that optimize the efficiency of the testing. EMC TestingKeystone Compliance is a unique EMC test facility because of our focus on assisting our customers achieve the measurements and certifications that they are seeking. Our lab features three 3-meter EMC chambers and two military/aerospace EMC chambers. In addition to the chambers, the lab significant ground planes, equipment and software that optimize the efficiency of the testing.Our EMC/EMI testing capabilities include but are not limited to:Radiated immunity testing up to 200 V/m from 10 kHz to 40 GHzRadiated emissions testing up to 40 GHzSurge testing to 10kV/10kA – and higherElectrostatic Discharge “ESD” testing up to 30 kVConducted immunity testing to levels well above the highest defined “standard” levelsMagnetic field immunity testing up to 100 A/m continuous and 1000 A/m short/impulseCustomized transient waveforms to extend level, duration and/or repetition of the standard’s definitionShielding Effectiveness from small panels and boxes all the way up to large enclosures and cabling, with a wide dynamic range all the way to 40 GHzWhat differentiates Keystone Compliance from other EMI test labs is our consultative engineering and expedited EMI test reports. Our staff understand EMC/EMI testing and has extensive experience with radiated immunity, radiated emissions, conducted immunity, conducted emissions, surge, ESD and shielding effectiveness testing. We also cater to specialized testing requirements. If you do not see the test standard or testing requirement you are looking for, please contact us as we may still be able to assist you.For more information about our scope of accreditation, please visit the links below.CISPR StandardsIEC/EN Product Family StandardsIEC/EN Test StandardsISO, SAE and Vehicle StandardsMilitary StandardsFCC, North American and International StandardsShielding Effectiveness TestingLightning and Surge Testing
