- Virginia Panel Corporation
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Lo...show more -
product
Signal, Contact, ITA, TriPaddle, 7 Amp, 26-28 AWG
610110169
Primary mating contact 610110167. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Micro Coax, Contact, ITA, RG178
610141102
Primary mating contact 610140102. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistanc...show more -
product
32-CH Discrete Input Daughter Board Module
HSL-DI32-DB-N
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
product
System Components
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
product
Cantilever type Probe Card / C type
CE Series
Japan Electronic Materials Corp.
*Standard Cantilever Probe Card*Low Contact force*Stable Contact*High accuracy of alignment*Suitable for variety of Devices
-
product
Tachometers
Labs use this high accuracy unit to check speeds of centrifuges, motors, or stirrers. Five digit LCD is a vivid ½-inch high display. Tachometer takes only three seconds for most readings. A unique memory feature permits recalling the highest, lowest, and last reading. Unit is extremely easy to use; operation may be learned in one minute. One end of the unit provides contact readings with a rotating spindle.
-
product
Digital Micro OHM Meter
NMC's Digital Micro Ohm Meters are low cost, compact, light weight, 3½ digit resistance meter suitable for measurements of resistances of cables, wires, transformers, motor windings, coils and contact resistance of switches, connectors, relays and track resistance of PCB's etc. The value of resistance is displayed on 7 segment LED display. Four terminal measurement systems provide measurements free from errors due to contact resistance and test lead resistance.
-
product
ITA, I2 Micro ICon, 168 Position, With Oversized Backshell
410130106
The i2 Micro iCon ITA with oversized cable clamp is capable of holding up to 168 QuadraPaddle contacts. With a wider 1.97” footprint, it is ideal for applications requiring shielded twisted pair wiring or other wire types with oversized jackets. The 30-degree u-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.80". The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
product
High DC Breaking Capacity (8A) Relays
D-YB Series
Heavy duty relays for demanding applications. Integrated magnetic arc blow-out function and double make - double break contacts for higher DC breaking capacity.
-
product
Infrared Thermometer
6575
Peaceful Thriving Enterprise Co Ltd
Infrared Thermometer is designed to measure surface temperature whereas traditional contact type thermometer is inappropriate. For example, measurement of moving object, items with live voltage, and items not reachable.
-
product
Signal, Contact, ITA, TriPaddle,7 Amp, 20-24 AWG
610110108
Primary mating contact 610110101. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. with Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Pressure Transducers and Transmitters
AMETEK Sensors, Test & Calibration
We provide some of the world’s most popular pressure transducers and pressure transmitters for a variety of applications and markets. For more information contact Us
-
product
Tool, Crimp, Micro Coax, Receiver and ITA
910101132
Tool Kit, Crimp, Micro Coax, f/ RG 316 and RG 179 wireIncludes p/n's 910101139, 910101135, 910101133.Used to crimp VPC micro coax contacts to RG316/179 wire. Includes receiver, ITA and crimp die.
-
product
Probe Card
VS Series
Japan Electronic Materials Corp.
*Vertical contact Probe Card with Spring*Suitable for Area array Bump Test
-
product
LXI Low Thermal EMF Matrix 1-pole 28x33
60-510-003
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
D10-AIO Conversion Set_for Conventional Panel-mounted Type Power Amplifier
PAD24
PAD24 DIO(digital input/output)-AIO(analog input/output) Conversion Set Conversion Set products. It could be used for DIO (Digital input/output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and another equipment which need AIO (analog binary input/output, dry contacts).
-
product
Contact Ultrasound Sensors
Inspect bearings, steam traps and perform other mechanical inspections with our Needle or Threaded contact sensors.
-
product
Dielectric Gloves & Boots Tester
Weshine Electric Manufacturing Co., Ltd
Rubber insulating gloves are among the most important pieces of personal protective equipment for electrical workers. They are the first line of defense for contact with any energized components.
-
product
Weights
Vetek only sells precision class M1 weights on our webshop. In most cases these act as ideal control weights. If you require weights with a certificate for first time verification, please contact us.
-
product
Threaded DryLoc pH/ORP Electrodes
2774-2777
The Signet 2774-2777 pH and ORP Electrodes feature a unique foulproof DryLoc connector with gold-plated contacts designed specifically for use with the Signet 2750 and 2760 preamplifiers and sensor electronics. These dependable and highly responsive electrodes feature a PTFE double reference junction with KNO3 in the front chamber to block various poisoning ions.
-
product
Battery Cell Formation System
17000 series
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy direct...show more -
product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
Hematology Analyzer
Pentra 80 Range
Malaria testing is optionally available on ABX Pentra XL 80 and Pentra XLR upon request towards your HORIBA Medical representative.*This product may not be available in your country or region at this time. Please contact your HORIBA Medical sales representative or distributor for more information.
-
product
Spring loaded type sample mounting board
SPCB
Mount samples on SPCB board without bonding wires.Spring loaded clamps helps to move probe pin easily x, y, z direction.Gold plated Non-magnetic phosphor-bronze constructionContacts on sample’s four point corner by soldering materials, such as InSn may still be required for good ohmic contact.
-
product
Laser Diode
Is a Polarization Maintaining CWDM Coaxial DFB-LD for CWDM analog communication, CATV return-path, laboratory instrument, and R&D applications. This cost-effective, high reliability DFB laser chip has a selectable wavelength with range between 1270 nm to 1610 nm. The versatile DFB-CWDM also features a built-in InGaAsP monitor photodiode, built-in optical isolator and 4-pin coaxial- pigtailed package, single mode coupling, and an FC/APC connector. Contact Optilab for more information.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Rotary Switches
Reliability and ruggedness are just two of Elma's core competencies for rotary switches and encoders. Panel and shaft sealing up to IP68 against dust and water are standard for all rotary switches. The shaft material for all switches is stainless brass or stainless steel – this is suitable for rugged environments. In order to guarantee years of undisturbed functionality and service life of the rotary switches, all electronic contacts are plated and provided with hard gold. In addition to a large selection of encoders, coding switches, selector switches, audio solutions and multifunctional rotary switches & encoders, Elma Electronic offers you also the right knobs and caps.
-
product
Pin-Line™ Header with Screw Machine Contacts
Series 0625
Pin-Line Headers with Screw Machine Contacts. Aries Pin-Line headers are available with a variety of screw machined contacts. Consult Data Sheet No. 12034 for strip-line headers with coined contacts. Break feature allows header to be cut to the number of positions desired.
-
product
Micro Power, Contact, Receiver, PCB Mount
610142108
Micro Power, Contact, Receiver, PCB Mount.
