- Pickering Interfaces Inc.
product
20-Pin GMCT Female Connector, 16A, With Backshell
40-960-020-16A-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. Also included is the backshell with screwlocks and cable clamp.
-
-
-
product
Clamp Meters, Clamp Multimeters
Hioki provides a wide range of models for AC, DC, and leakage current measurement. The lineup also includes DC high-voltage probes for measuring the open-circuit voltage of high-voltage solar power (PV) systems. Models that can be easily inserted into narrow gaps between cables and transmit data to smartphones or tablets improve operational efficiency.
-
product
Absorbing Clamp
AB-CLP
• EMI Receiver equipped with absorbing clamp can indirectly test radiated interference power of household electrical appliance, power tool and similar electrical appliance with frequency from 30~300MHz.
-
product
Absorbing Clamps
The Absorbing Clamp was designed to measure the disturbance power according to CISPR 16-2-2 in the frequency range 30-1000 MHz, it complies to the technical requirements of CISPR 16-1-3.
-
product
Absorbing Clamps
The absorbing clamps also known as ferrite clamps are used for measuring disturbance power on power input lines as well as other auxiliary I/O lines.
-
product
Amp Clamp
PPDCM80
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
product
Clamp Meter
ST-3347W
Standard Instruments Co., LTD.
This clamp meter provides accurate AC, AC/DC current and voltage readings regardless of the waveforms. This meter can use in most industrial and commercial applications where non-linear loads distort the current or voltage waveform. Reliable operation. Features accessories such as test leads, carrying case and temperature probe.
-
product
Clamp Meter
ECLIPSE
ECLIPSE has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp is provided with a display with 6000 measuring spots with backlight and bargraph to allow for a simple reading even in poorly lit environments.
-
product
Clamp Meter
KT-266
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and resistance measurementData hold function50 mm Large jaw DiameterPlug - insulation tester, adapter 500 VDC (optional)Audible continuityLow power indication
-
product
Clamp Meter
Shenzhen Graigar Technology Co.,Ltd.
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
Clamp Meter
KT-266C
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and resistance measurementTemperature test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Audible continuity test, Data holdLow power indicationSpecificationSpecificationsRangeAccuracy±(%rdg + digits)AC Voltage 200/750V 1.2%rdg+10dAC Current 20/200/1000A 2.0%rdg+5dDC Voltage 200mV 0.5%rdg+1d2/20/200V 0.8%rdg+1d1000V 1.0%rdg+2dResistance 200/20K/2M Ω 1.0%rdg+2dTemperature 0 - 400°C 1.0%rdg+3d400 - 750°C 2.0%rdg+1dDimensions 230mm(L) x 70mm(W) x 37mm(H)Unit Price (USD) 4.0Min.Quantity (pcs) 1000Weight(g) 310pcs/carton 34N.W. 10.6G.W. 11.5Packing carton size 52 x 36 x 40 cm
-
product
Clamp Meter
KT-266F
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and Resistance measurementFrequency test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Audible continuity, Data hold ,Diode testLow power indication
-
product
Clamp Meter
IDVM333
Plug the iDVM333 directly into the iDVM510 multimeter and measure AC millivolts with no need to break the circuit. This feature measures high amperage.
-
product
Clamp Meter
KT-3070B
Jaw size: φ50mm3 1/2 digits LCD, maximum reading 1999 counts Peak hold Diode test, Continuity testMeasure starting current of electric motor
-
product
Clamp Meter
It can be used for CURRENT, VOLTAGE and FREQUENCY measurements on installations of surge voltage.
-
product
Clamp Meter
KT-3500
• Non - intrusive AC and DC current measurement• 10mA resolution• Average responding, RMS calibrated• Auto ranging /Auto zeroing• Data Hold • Low battery indicator• Auto Power OffMeasuring Range: 0 - 500A DC or ACAuto ranging : 50A/500AResolution: 10mA in 50A range, 100 mA in 500A rangeBasic Accuracy: ±1.3% rdg ±5 digitsTemperature coefficient: ±0.05% of rdg /°CFrequency range: DC in DC: 40 HZ to 400 HZ in ACOverload capacity: 500 ADielectric strength: 3.7 KV RMS.50 Hz 60s(EN61010-2-032 Cat III...show more -
product
Clamp Meter
KT-266FT
3 1/2 digits LCD with max. reading of 1999AC/DC voltage and resistance measurementTemperature & frequency test50 mm Large jaw DiameterPlug - insulation tester adapter 500 VDC (optional)Data holdLow power indication
-
product
Clamp Meters
TES Electrical Electronic Corp.
Variable Frequency drive measurement. LoZ voltage measurement to drain ghost voltages. Check 3phase sequence. True RMS reading on AC and DC+AC mode. Inrush current measurement. A measurement for HAVAC flam sensors.
-
product
Clamp Meters
The Compact Clamp Meter, incorporates a lot of big meter functions into a compact, easy to use design. While it’s not exactly an all-in-one multimeter, this auto ranging digital multimeter is an affordable meter for the HVACR electrical testing HVACR professionals use everyday. Along with standard multimeter ranges, we designed the SC220 to include microamps DC for flame rectification. Add to that, we designed it with built-in non-contact voltage and a continuity beeper to give you a powerful HVACR meter that’s under 8-inches tall. Makes a great backup or a solid performer for everyday testing.
-
product
Clamp Meters
UEi Test & Measurement Instruments
Combine meter and current probe into integrated instrument.
-
product
Clamp Meters
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional clamp meters manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable clamp meters in stock from us. Check the quotation with us now.
-
product
Clamp Meters
Our clamp meters measure both high and low AC and DC currents as well as earth leakage and earth resistance. With variable jaw sizes, max current readings up to 2000A AC/DC and features including TRMS, data logging and temperature readings we have clamps suitable for a wide range of electrical applications.
-
product
Clamp Meters
Is an electrical test tool that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
Clamp Meters
Sanwa Electric Instrument Co., Ltd
An electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
Clamp Meters
Amprobe invented the first clamp meter in 1948 and has continued to innovate and evolve. Today Amprobe offers several categories of clamp meters – from the rugged CAT IV rated Navigator Series, to the versatile Swivel clamp meters, to the compact mini-clamps. Whether you work on residential, commercial, or industrial applications you’ll find an Amprobe tool that fits your needs.
-
-
product
Clamp Meters
The Delta series consist of clamp meters and clamp CT''s. This meter is basically used where the electric current in the conductor can be measured, without having to make physical contact with it.
-
product
Clamp Meters
Milwaukee Electric Tool Corporation
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
Clamp Meters
Clamp meters are handheld devices with multimeter functions and able to measure AC/DC current directly without breaking the electrical conductor. Today’s clamp meters are multi-functional designed and used in HVAC/R, electrical vehicles, electrical installation, motor inspection, engineering, and many other applications. UNI-T clamp meters are well known for its performance, practicality, and reliability.
