Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Fixture Kit
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
-
-
product
Functional Fixtures
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
product
Test Fixtures
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
product
Test Fixture
OCP NIC 3.0
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
product
Accessories: Fixture
ICT I3070
View ICT i3070 fixture accessories ranging from fixture kits to vectorless test items like nanoVTEP. You can conveniently select items/parts to request for a Quick Quote.
-
product
Fixture Kit
MF500
Electronic Test Fixture Kit Very low-cost kit facilitates use in situations where traditional fixtures are too expensive:o Research & Developmento Engineeringo Low-volume Production Uses include:o Debuggingo Programmingo Verification and Test
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
-
product
Fixtures For Testing
Columbia offers a wide range of different fixtures and test equipment that are possible to modify according to your needs of testing. Our range of different types of test fixtures goes from ICT, RF, General Purpose, CMP to CMK.
-
product
Custom Fixtures
The shock and vibration fixture model BW-SV-3X3X3 is designed to accept up to 24 each of the TO-3 packages on each of the 6 axes and mount to the vibration shaker model BW-100C and Shock Tester model BW-E5000. The fixture is made of white derlin and measures 3”x3”x3”and weighs approximately 13 ounces. The fixture includes a white derlin cube with a 2 ¼” bolt circle and 4 10-32 x 3” cap screws.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
In-Circuit Fixtures
In-Circuit test fixtures can be configured for dual stage, dual well and opens testing applications. Even the most complex boards can be accommodated using standard methods of actuation.
-
product
Test Fixtures
At A.T.E Solutions we have a dealt with a wide range of test subjects in the past 30 years and have extensive experience in providing reliable test fixture solutions.
-
product
Test Fixtures
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Test fixtures
Offers a wide range of standard Test Fixtures that can fit many of your applications and services. From your R & D to your production lines, we have a solution for you.Each products are standard but we can adapt or design your application.
-
product
Test Fixtures
Canadian Microelectronics Corp.
This fixture clamps to microstrip or CPW lines at the edge of an RF board and is usable at any position without limit on size of circuit. The base is magnetic and it can be locked and released by a knob to accommodate any kinds of circuit configuration. Available for frequency ranges up to 40 GHz.
-
product
Pod/Nest Fixtures
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Fixture Identifier
YAVCANCON2
This module is designed to give all necessary data to the test system, related to executive software selection, system protection against human errors, automatic adjustment of conveyors and preventive maintenance management through test cycles counting. The module features two independent counters to cover dual dwell fixtures, that are incremented either through pressure system, switch-probe contacts or through CAN bus.
-
product
Custom Fixtures
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
product
Test Fixtures
At Global Test Services LP, we know that verifiable yields are the backbone of your business, which is why we offer innovative, robust solutions that offer you better availability, improve efficiency, and offer flexible, scalable systems that meet the specific quality and test needs of your business.
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
ESS Fixture
ESS - Environmental Stress Screening - is not a test. It is a product level screening process. ESS is part of manufacturing process, that verifies the operational parameters and guard bands of a product from an environmental - temperature, shock, vibration - point of view.
-
product
Module Fixture
Design according to customer's requirementsUse on auto or semi-auto test eqiupments and handler.Pitch range from 0.30mm and above.Pin amount: 2 and above.Key material: Peek,Torlon,PPS,PEI.etcContact with top pogo pin
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
