Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
WiFiScope WS6+EMI: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XME-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
-
product
LAN Tester
TVR10/10/100
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
product
LAN Module
Axiomtek provides various LAN modules for network appliances, such as GbE copper module, GbE fiber module, 10GbE copper module, 10GbE fiber module and more.
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
LAN Switches
Featuring user-friendly efficient IP management, IPv4 and IPv6 hardware Layer 3 routing, PLANET LAN switches are designed for SMBs, system integrators and large enterprises when managing wide coverage networks. Apart from providing 10Gbps~100Gbps high performance managed switches, PLANET Ethernet switches, which come with unique Color LCD Touch Screens for efficient management purposes, are also designed with user-friendly fast installation and real-time monitoring.
-
product
Wireless LAN
PLANET comprehensive wireless LAN solution includes hardware and software AP controller, and indoor and outdoor APs. Featuring the latest 802.11ac wireless technology, and 2.4GHz and 5GHz bands, PLANET wireless solution provides ultra-speed transmissions, stable connectivity, wide coverage and superior encryption for excellent multimedia streaming, surveillance monitoring, Internet access and more. The AP control function, featuring central management over up to 1024 various kinds of wireless APs, perfectly suits hotels, campuses, public infrastructure applications and more.
-
product
LAN Testers
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
product
LAN Cable Tester
LAN-1
The LAN-1 Cable Tester is designed for testing opens, shorts and miswired cable installations. It is designed to work with various data cables and connectors. This cable tester provides a quick go / no-go LED display of the wiring and connection of item under test. You can either step through the test cable wiring one at a time or have the unit automatically pulse through the pin-outs and display the results.
-
product
Digitizer/Oscilloscopes for LAN Ethernet
Wuntronic Lan Ethernet Digitizers & Lan Oscilloscopes
-
product
LAN⇔RS-232C Conversion
SI-60F
SI-60F is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). It is the environment-friendly design, such as low power consumption from DC5V and compact body (resource saving).
-
product
LAN⇔RS-232C Conversion
SI-60
SI-60 is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. Therefore, you can use it for factory automation without worry.
-
product
LAN Cable Tester
21-6566-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
-
product
LAN Cable Tester
21-6568-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
-
product
LAN Cable Tester
Is a hand-held test instrument that lets you verify and troubleshoot the LAN cable of twisted pair. It displays graph wire-map, opens, shorts, miswires, split pairs and the remote ID number all on one screen.
-
product
LAN Packet Tester
LE-590TX
The LE-590TX is a LAN analyzer that connects to a PC's USB2.0 port. In TAP mode, you can capture full duplex data on 10/ 100Base-TX and transmit to the PC at 480Mbps via the USB2.0 interface. In PG mode, you can generate test packets at up to 100Mbps line rate.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
*is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.*by comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit.*provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
LAN Tester RJ45
CZ20250
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Mini Lan Tester
21-8572-00
Auto decipher the straight and cross-over pinning?RJ45 each pair connected display.
-
product
Wireless LAN Module
SX-SDMAC2
The SX-SDMAC2 is a dual band IEEE802.11 a/b/g/n/ac WLAN and Bluetooth 5.0 BR/EDR/LE (Class1) module based on Qualcomm QCA9379-3 chipset. It supports 2x2 antenna configuration for applications that require higher performance. Silex has separated the Bluetooth antenna from the Wi-Fi by creating a third antenna port, allowing concurrent operation of Wi-Fi and Bluetooth further optimizing the Wi-Fi and Bluetooth performance.
-
product
Lan CAble Testers
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
product
Lan Cable Tester
3PK-NT015N
Open/short wiring testConnected wires displayNo wire or termination indicationWrong connection / Non-parallel connectionEthernet 10 base2 termination value detectionBattery low indicationBuzzer insideBNC for testing 10 BASE2 terminator valueIsolation resistances 50 K ohms test
-
product
LAN Cable Tester
21-8569-00
Open / Short / Misswiring test?BNC / RJ45 each pin connected display?No wire or termination?Isolation Resistances 50K ohms test
-
product
LAN Network Testers
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
product
Mini Lan Tester
21-8580N-0
Auto decipher the link status is NIC or Hub.?The deveices is working in 100 Base -TX Full Duplex 10 Base-T Full Duplex or Half Duplex?The deveiceis transmitting a pack or not?Data transmitting error has occurred
-
product
DataComm & LAN Testers
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
-
product
LAN⇔RS-232C(2ports) Converter
SI-60X
SI-60X is an interface converter that converts 2 serial ports of RS-232C devices to Ethernet LAN at 10Base-T/100Base-TX. The built-in Lantronix WiPort® NR on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. The small housing ensures ease of use for FA applications, public facility and medical institution as a communication device server.
