- Virginia Panel Corporation
product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-422/485
540041010201
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
product
- RS-232 to RS-422 Interface Converter
Model 263
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
product
Universal Pylon Tester
MS 1121
Portable test equipment to check the electrical functionalities of pylons by simulating various store types in aircraft. This system is able to simulate the functionalities of different PIBs (IB/MB/CF, OB & Laser). The system provides facility to test two Pylons in parallel. The tester provides aircraft specific AC &DC voltages and facility to inject discrete inputs for checking output(s) viz firing voltages, fusing voltages. The system provides four channels of RS422 and Two channels of 1553B communication. Portable unit with caster wheels with all required hardware, power supplies, instruments, connectors and laptop housed in it.
-
product
Tunable Filters
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
product
4 Port cPCI Card
GX3904
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 Ω parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Unive...show more -
product
ARM LPC3250 Board
MS 1509
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Receptio...show more -
product
Protocol Converter
MACC
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the uni...show more -
product
Dual Channel Multi-Band FM Tracking/Data Receiver In Modular Style Housing
LS-27-B
The Lumistar LS-27-B Modular Dual Channel Tri-Band Tracking and Data Receiver is Lumistar’s third generation of modular high performance FM Receivers. This wideband designs supports one or two independent channels of PCM with data rates up to 20Mbps. The unit includes both an optional FM demodulated output for PCM data, and standard programmable AM/linear AGC outputs for auto-tracking receivers. The design offers 8 IF Bandwidths and 8 Video Filters per channel for each receiver.AC coupling with ...show more -
product
RS232 / RS485 / RS422 To Fiber Optic Converters
Our rugged, industrial-grade, point-to-point RS232 / RS485 / RS422 serial to fiber optic converters work in pairs to extend serial signals (RS232, RS485, RS422, and TTL) over long distance. These point-to-point RS232 / RS485 / RS422 serial to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode (extend distance up to 3 miles / 5km) and single-mode (extend distance up to 25 miles / 40 km), and ST, SC, and FC connectors.
-
product
Multi Protocol Analyzer
LE-3500R
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
product
PXI-8433, 4-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779539-01
4-Port, Isolated, RS485/RS422 PXI Serial Interface Module—The PXI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Compact Protocol Analyzer
LE-1500R
"LE-1500R" is a protocol analyzer (line monitor) dedicated for asynchronous communication monitoring with affordable pricing. LE-1500R can run as a stand- alone by the internal battery for long time and can be remotely controled by a PC or a smart phone via Wi-Fi (Wi-Fi function is available only in USA, Canada, Japan, and EU). The analyzer has a TTL measurement port (which supports UART communication) as its standard port besides RS-232C, RS-422, and RS-485. It can monitor communication data o...show more -
product
Event Counter
MS 2022
Event counter is sleek system used to keep track of events. Event counter system is an independent unit with LED, event and reset buttons used for user interface. User generated events are displayed by LED (seven segment display scheme). Event counter Board consists of Microcontroller, counters, monostable multivibrator, transmitters & receivers (RX232, RX422). Event button is used to increment the events and reset button is used to reset the count value. Events are displayed on seven segmen...show more -
product
Serial Interface Device
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS...show more -
product
PMC-BiSerial
Two fully independent and highly programmable RS-485 / RS-422 IO channels are provided by the PMC-BiSerial design. The channels are supported by two independent state-machines created within the Xilinx FPGA. The transmit and receive protocol can be the same or different. Manchester encoding and decoding, standard serial [UART], control, command, instrumentation, and custom protocols can be implemented.
-
product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Mission Computer Software Integration Rig
MS 1124
The HSIR is the ground test facility and it simulates various LRUs/sensors interfaced with the HAWK Mission Computer. RIG consists of Industrial computers with Simulation modules, Acquisition modules, Video generator module and video display monitors. RIG provides the simulated inputs to both the MCs from each simulated sensor/ LRU through hardwired signals, through the MIL-1553B, Arinc 429, RS-422, RS232 and Ethernet etc. The rig is capable of testing two MCs together either of which can be use...show more -
product
Single Port RS-422/485 Serial PCMCIA Card With Detachable Cable
SSP-200/300
The Quatech SSP-200/300 offers a convenient way to add a single RS-422/485 serial port to your laptop, PDA, or desktop (using one of Elan's Desktop PCMCIA adapters - P111, P222 etc.). The card automatically configures to become another COM port using the supplied drivers that are tried, tested, and optimized for Windows.
-
product
Universal PCI, Eight or Four-port RS-232/422/485 Serial Communication Card
LPCI-COM Series
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis.
-
product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Ope...show more -
product
GPIB Smart Serial Interface
Model 4866
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
GPIB Instrument Control Device
GPIB Instrument Control Devices offer IEEE 488 controllers that are compatible with ExpressCard, PMC, PCMCIA, PCIe, PCI, and USB slots as well as Ethernet, RS485, RS422, and RS232 ports. Some models can control multiple GPIB devices, and others offer sustained data transfer rates and no microprocessor interruption in data transfers. GPIB Instrument Control Devices include a license for the NI-488.2 driver software, providing maximum reliability for connecting to third-party instruments via GPIB. The devices are completely IEEE 488.2 compatible, have industry-standard transfer rates, and offer easy system configuration through NI software.
-
product
GPIB-RS485, GPIB Instrument Control Device
779733-04
Serial, RS485/RS422 GPIB Instrument Control Device - The GPIB‑RS485 is an IEEE 488 controller device for PCs with RS485 or RS422 ports. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS485 or RS422 … serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS485 and RS422 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 48...show more -
product
Multiport Serial Adapter, PCIe X4
PCI325
The PCI325 is an RS-422 synchronous/asynchronous multiport serial adapter. The module can accept a clock input to synchronize the baud rate generators of each port to an external clock. All the protocol management overhead is taken care of in the hardware so that the host CPU is offloaded from managing the detailed serial protocol. An I/O breakout box may be connected to the high-density connectors of the PCI325 to provide multiple DB25, DB9, or other serial connectors for easy integration to yo...show more -
product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote ...show more -
product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, 10MHz RS-422 Inputs
APCIE-1711-10MHZ
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each...show more -
product
USB⇔RS-422/RS-485
SI-35USB
SI-35USB is an USB converter, which converts USB of PC into RS-422/RS-485.
