Filter Results:
Products
Manufacturers
Applications
Seismic Accelerometers
sense ground vibration.
See Also: Seismic, Seismometers, Seismic Arrays, Earthquake
-
product
High Sensitivity Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Typical fields of application include the monitoring of buildings, dams, bridges, oil platforms and pipelines. These sensors are often called seismic accelerometers because they are used to monitor construction activity, volcanoes and earthquakes. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
product
Accelerometers
A device that measures the vibration, or acceleration of motion, of a structure.
-
product
Accelerometer
BC 201
The BC 201 acceleration meters are capacitive acceleration meters and can be used as linear acceleration and position sensors since they measure not only the variable component of the acceleration signal, but the direct component as well.
-
product
Accelerometers
Accelerometers measure linear acceleration. They can be also used for specific purposes such as inclination and vibration measurement. MEMS accelerometers embed several useful features for motion and acceleration detection, including free-fall, wakeup, single/double-tap recognition, activity/inactivity detection and 6D/4D orientation.
-
product
Accelerometers
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
product
Seismic Digitizers / Recorders
SMART Series
The SMART Series of instruments represent the logical solution for seismological data acquisition: a common design for a digitizer, portable recorder, and strong motion recorder(the all-in-one solution).
-
product
Analog Seismic Sensors
Seismometers
Designed to yield the performance needed for scientific studies, our seismometers are used for monitoring long period (very low frequency) signals. These units are often used for earthquake monitoring and for triggering potential alerts during natural disasters such as tsunamis.
-
product
Quantum Accelerometer
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
product
Accelerometers
Velocity sensors and several types of accelerometers made to industrail standards for measuring vibration in a variety of applications and detecting potential machine failures before they occur.
-
product
Accelerometers
Columbia Research Laboratories
An instrument for measuring acceleration, typically that of an automobile, ship, aircraft, or spacecraft, or that involved in the vibration of a machine, building, or other structure.
-
product
Seismic Sensor
SmartPhone D
Teledyne Marine Real Time Systems
The highly rugged encapsulated SmartPhone D was designed for use with the SmartSource controller, or SmartPhone D system, for real-time monitoring of near-field signatures.
-
product
Accelerometers
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
product
General-purpose Accelerometer
MTN/1100
General-purpose accelerometer with isolated AC outputs, ideal for vibration analsis and for use in harsh environments.
-
product
Accelerometers | Vibration Sensors
Accelerometers measure the levels of vibration in an engine or system. They detect faults and prevent potential damage. They enable you to achieve the reliability and accuracy you need for your engine, aircraft, helicopter, UAS, space or transportation application.
-
product
Seismic Sensors & Transducers
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference. A transducer within the pickup senses the motion of the mounting base relative to the inertial reference and converts it into a proportional signal. Appropriate damping results in a frequency response flat down to 10 Hz. Note that the pickup senses in only one plane, which is perpendicular to the mounting base.
-
product
Accelerometers
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
product
Digital Accelerometer
ZET 7151
The characteristics of the primary transducer are set in the device memory and measurements are performed based on those parameters. Thus, the digital sensors releases the user from setting the measuring channels and data processing. The sensors are fixed on the measurement object while the information transmission units are mounted in electric cabinets. An advantage of the ZETSENSOR units is easy installation and uninstallation as well as indication of feed and signal transmission which, in its turn, facilitates diagnostics of the system at the facility.
-
product
Digital Accelerometer
ZET 7052-N
Digital accelerometer ZET 7052-N is equipped with a compact sensing element and is designed for linear acceleration and vibration acceleration variable constituent measurement via three mutually perpendicular planes. Small weight of sensing element (1,5 g) considerably reduces self-mass load and compact dimensions (8,5×8,5×8,5 mm) enable use of the digital accelerometer ZET 7052-N for vibration measurements in systems with small active area.
-
product
USB Digital High-Resolution Accelerometer
Digiducer 333D01 USB digital accelerometer is the first fully integrated and ruggedized packaging of a high-resolution, broad-frequency piezoelectric accelerometer with integrated internal digital data acquisition. When used in conjunction with Multi-Instrument® software, the setup allows you to take reliable and quality vibration measurements as simply as plug & play. No external power supply, data acquisition hardware, driver installation and manual entry of sensor sensitivity are required. It is a truly hassle-free portable vibration test & measurement solution.
-
product
Accelerometers
353B15
Sensitivity: (10 %);10 mV/g 1.02 mV/(m/s) Measurement Range:500 g pk 4905 m/s pk Frequency Range:(5 %)1 to 10000 Hz1 to 10000 Hz Frequency Range:(10 %)0.7 to 18000 Hz 0.7 to 18000 Hz Frequency Range: (3 dB)0.35 to 30000 Hz0.35 to 30000 Hz Resonant Frequency:70 kHz,70 kHz Broadband Resolution (1)0.005 g rms0.05 m/s rmsNon-Linearity:1 %1 % Transverse Sensitivity:5 %5 %
-
product
Servo type Accelerometer
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
product
Seismic interpretation Software
GeoTomCG
GeoTomCG can process crosshole or VSP seismic or radar data. The display shows calculated radar velocities. High velocity zone at depth of 27 m is caused by an abandoned mine. Other zones of contrasting velocities are geological features. S and R indicate source and receiver positions, respectively.
-
product
1-axis Accelerometer GF1
Panasonic Industrial Devices Sales Company of America
Acceleration sensor
-
product
High Performance Linear Accelerometers
Columbia Research Laboratories
The sensors featured in Columbia's High Performance Force Balance Accelerometers offer extremely rugged, high performance accelerometers. These sensors are used in applications ranging from severe vibration and shock environments, to demanding missile and airborne applications and downhole well servicing applications. Columbia also offers high temperature and miniature High Performance Sensors.
-
product
Advanced Seismic Source
GI-SOURCE
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
product
Digital Accelerometer
ZET 7152-N Pro
Digital accelerometer ZET 7152-N Pro is intended for recording of vibrational acceleration and is used as a component of stationary vibration monitoring systems used in technological and industrial spheres of application.
-
product
MEMS Accelerometers
Safran designs and manufactures high-precision tactical grade MEMS acceleration sensors and mems inclinometers for demanding applications in the Defense, Aerospace, Industrial, and Commercial markets. Safran’s journey as a global leader in MEMSMicroElectroMechanical System. See also technology spans decades. Our extensive experience has not only honed our expertise but also enabled us to develop ITAR-free solutions. This means our MEMS technology is readily available for a wide range of applications, without the constraints of International Traffic in Arms Regulations (ITAR).
-
product
Miniature Triaxial Accelerometers
Miniature triaxial accelerometers are available in a variety of sensitivities to suit specific application requirements. These small and lightweight units have a high frequency response and minimize mass loading on test structures. They are ideal for installation in space restricted locations
