- TEAM SOLUTIONS, INC.
product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Compute Express Link (CXL)
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
product
PCI Express 5.0 and Compute Express Link Protocol Exerciser
Summit Z516
The Summit Z516 is a PCIe 5.0 and CXL protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z516 can emulate PCI Express 5.0 and CXL root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyze
Your product description goes here.
-
product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyzer
Summit T516
The Summit T516 is targeted at high-speed PCI Express 5.0 and CXL I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
product
PXIe-8381, x8, MXI-Express Interface, PXI Remote Control Module
782362-01
PXIe, x8, MXI-Express Interface, PXI Remote Control Module—The PXIe‑8381 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCIe‑8381 through a copper, x1 MXI‑Express cable.
-
product
PXIe-8398, Gen 3, x16 PXI Remote Control Module
784178-01
PXIe, Gen 3, x16 PXI Remote Control Module—The PXIe-8398 enables control of a PXI Express chassis from an external host, such as a desktop PC, rackmount controller, or a separate master chassis. Using a Gen 3 x16 PCI Express link, the PXIe-8398 provides up to 16 GB/s of data transfer between the chassis and host over a copper cable connection.
-
product
PXIe-8399, Gen 3, x16, 2-Port PXI Remote Control Module
784180-01
PXIe, Gen 3, x16, 2-Port PXI Remote Control Module—The PXIe-8399 enables control of a PXI Express chassis from an external host, such as a desktop PC, rackmount controller, or a separate master chassis. Using a Gen 3 x16 PCI Express link, the PXIe-8399 provides up to 16 GB/s of data transfer between the chassis and host over a copper cable connection. An additional port allows daisy-chaining for multi-chassis configurations.
-
product
PCIe Gen3 x8 FMC Module
VITA 57.1 FMC HPC ConnectorPCIe Gen3/Gen2/Gen1 x8 Slot (upto 64Gbps)Single module supports both PCIe Root Port & EndpointM.2 Key-M NVMe slot with PCIe Gen3 x2 interface & SATA3.0 interfaceMIPI DSI & CSI Connector through LVDS IOs32Kb-EEPROM
-
product
Compact PCI-Express/PXI-Express Module
ACE1553-3U-x
The ACE1553-3U-x is a member of AIM’s new family of compact PCI-Express/PXI-Express modules for analyzing, simulating, monitoring and testing
-
product
Compact PCI-Express/PXI-Express Module
ACE1553-3U-x-DS
The ACE1553-3U-x-DS is a member of AIM’s new family of compact PCI-Express/PXI-Express modules for analyzing, simulating, monitoring and testing MIL-STD-1553A/B databuses providing 1 or 2 dual redundant bus streams.
-
product
PXIe High Performance System Module: Dual Port (x16), Gen 3
M9023A
The M9023A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The M9023A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
product
PXIe System Module: Single Port (x8), Gen 3
M9022A
The M9022A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The module can also be used with an M9037A PXIe embedded controller to interconnect two chassis in a multi-chassis system.
-
product
ARINC429 PCI Express Mini Card
AMEE429-x
The AMEE429-x is AIM’s new PCI Express Mini Card module targeted for embedded ARINC429 applications in an ultra-compact form factor.
-
product
Embedded MIL-STD-1553 PCI Express Mini Card
AMEE1553-x
The AMEE1553-x is AIM’s new PCI Express Mini Card module targeted for embedded MIL-STD-1553B applications in an ultra-compact form factor.
-
product
PCI Express Optical Link Board
SIS1100-E2
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
product
CXD Compute Nodes
All the benefits of traditional infrastructure deployed in colocation, available on-demand
-
product
Edge Compute Solutions
Innovate in real time. With the world’s largest serverless compute platform, Akamai puts your code closer to your users.
-
product
Mini Compute module
3 Model B
The Raspberry Pi 3 is the third generation Raspberry Pi. It replaced the Raspberry Pi 2 Model B in February 2016. Compared to the Raspberry Pi 2 it has: A 1.2GHz 64-bit quad-core ARMv8 CPU, 882.11n Wireless LAN, Bluetooth 4.1, Bluetooth Low Energy (BLE). 1GB RAM, 4 USB ports, 40 GPIO pins, Full HDMI port, Ethernet port, Combined 3.5mm audio jack and composite video, Camera interface (CSI), Display interface (DSI), Micro SD card slot (now push-pull rather than push-push), VideoCore IV 3D graphics core.
-
product
Optical Link
OPT-2
The OPT-2 Optical Link allows the THERMES-USB to be operated with total optical isolation between THERMES and the host computer. USB Isolation device offers up to 4500 volts DC isolation.
-
product
Camera Link
R3-CL
The R3 frame grabber family has been designed to simplify the task of interfacing today's Camera Link cameras to a wide array of imaging applications. The R3-CL can acquire from almost every Base CL camera manufactured.
-
product
Link Analyzers
RF BMLA+
Hollis Electronics Company LLC
Hollis Electronics Company (HEC) BMLA+ is a unique product that provides telecommunications equipment operators the ability to continuously monitor their IF and RF data links for equalization performance without taking the link off-line.
-
-
product
Innovative Compute Solutions for Medical Imaging
Cutting edge medical compute and image processing solutions optimized for medical imaging and surgical equipment. Radisys is a chosen Global Preferred Supplier for a major healthcare and imaging equipment provider.
-
product
CPCI Advanced Compute And IO Board
Advanced Compute & IO Board is high end Microprocessor based Mixed Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have digital I/O signals, analog I/O signals, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic (Programmable) data acquisition and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
product
High Speed Links
HSL
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).
-
product
PC Link Software
LE-PC800G
*The PC Link is software that provides an efficient measurement environment utilizing the high-resolution screen and high-capacity HDD of a PC.*The analyzer can be remotely controlled by the PC so that measurement data will be displayed on the screen or continuously recorded on the HDD.*The PC Link incorporates versatile features (e.g., a search function that finds target data exactly, a TEXT-CSV conversion function that is useful for the generation of reports, and Japanese-English display).
-
product
PC Link Software
LE-PC300G
LE-PC300G is Windows® software which enables a PC to control LINE EYE protocol analyzers from remote in order to use measurement data of those analyzers on a PC. It is compatible with the following analyzers: LE-3500, LE-2500, LE-1500, LE-7200, LE-3200, LE-2200 and LE-1200.
-
product
PC Link Software
LE-PC300R
LE-PC300R is a Windows® software with which you can control the protocol analyzer remotely from a PC and utilize the measurement data of the analyzer on the PC.
-
product
Camera Link Simulator
CLS-221
The CLS-221 Camera Link Simulator is an affordable, high-performance video test pattern generator that supports all video formats including those introduced in the new version 2.1 specification. Fully programmable video timing enables the CLS-221 to mimic the characteristics of almost any camera. New features include enhanced timing performance, bayer color support, and additional video patterns. Control is via an RS-232 port, USB, or frame grabber COM port. The CLS-221 also incorporates the AIA validation test pattern.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
