JTAG Boundary-Scan Controllers
Corelis has developed a wide range of high-performance boundary-scan controllers that are compatible with buses such as USB 2.0, PCI, PCI Express, and Ethernet. Many of Corelis’ boundary-scan controllers operate up to 100 MHz sustained TCK frequency.
- JTAG Boundary-Scan Hardware
- JTAG Boundary-Scan Controllers
- I2C Serial Bus Protocol Analyzers and Exercisers
- JTAG Boundary-Scan I/O Modules
- JTAG Boundary-Scan Controllers for High-Volume Production Systems
- JTAG 3rd Party Controller Support
-
product
JTAG Boundary-Scan Controller
NetUSB-1149.1/SE
8-TAP USB 2.0 and LAN Based JTAG Controller. The NetUSB-1149.1/SE is an advanced 8-TAP USB 2.0 and LAN-based JTAG/boundary-scan controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
High-Speed USB 2.0 JTAG Controller
USB-1149.1/1E
The USB-1149.1/1E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/1E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
PCI Based JTAG Controller
PCI-1149.1/Turbo
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
product
Remote Intelligent Pod
ScanTAP
The test patterns generated by the PCI-1149.1/Turbo controller are distributed to the target system either directly through ScanTAP 4 and ScanTAP-8 pods. The ScanTAP-4 and ScanTAP-8 pods can apply test vectors and/or ISP patterns to target boards with a variety of JTAG chain topologies. In the simplest case, the ScanTAP-4 and ScanTAP-8 will provide the interface between the PCI-1149.1/Turbo controller and a target system consisting of a single JTAG Test Access Port (TAP). This would be the case where the target system consists of one JTAG chain and its single associated TAP.
-
product
JTAG Boundary-Scan Hardware
JTAG Boundary-Scan Hardware by Corelis, including boundary-scan controllers, 12C serial bus protocol analyzers & exercisers, JTAG boundary Scan Modules, high-volume production JTAG systems, 7 support for 3rd party JTAG controllers
-
product
High-Speed USB 2.0 JTAG Controller
USB-1149.1/1E
The USB-1149.1/1E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/1E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
Single-TAP CFM JTAG Controller for Teradyne ICTs
USB-1149.1/CFM
The USB-1149.1/CFM High-Speed single-TAP boundary-scan controller makes adding JTAG test to Teradyne ICTs a snap. Designed specifically for integration into Teradyne TestStation and GR228x testers, the USB-1149.1/CFM offers a clean, convenient boundary-scan solution.
-
product
PCI Based JTAG Controller
PCI-1149.1/Turbo
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
4 TAP JTAG Boundary-scan Controller for Teradyne Systems
QuadTAP/CFM
The Corelis QuadTAP/CFM high-speed multi-TAP boundary-scan system makes advanced, multi-TAP boundary-scan testing within ICT systems a reality. By combining ICT and boundary-scan, test engineers gain benefits from both technologies for the highest possible test coverage, speed, and capability.Specifically designed for integration into Teradyne TestStation and GR228x testers, the QuadTAP/CFM and QuadTAP/CFM Expander enable a clean, convenient multi-TAP boundary-scan solution.
-
product
High-Performance LAN & USB JTAG Controller
NetUSB II™
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires a controller with high performance specifications and diverse features.
-
product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
product
Boundary-Scan Test and In-System
PCIe-1149.1
The Corelis PCIe-1149.1 is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the PCIe-1149.1 offers up to 80 MHz clock rates on 4 or 8 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
-
product
JTAG Boundary-Scan Controller
NetUSB-1149.1/SE
8-TAP USB 2.0 and LAN Based JTAG Controller. The NetUSB-1149.1/SE is an advanced 8-TAP USB 2.0 and LAN-based JTAG/boundary-scan controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
-
product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locations. Other features include signal delay compensation for long cable lengths to the UUT, TAP signals, and GPIO discrete signals which are individually programmable from 1.25V to 3.3V, programmable slew rate control and pre-power up test for shorts between power and ground traces on the UUT.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
JTAG Emulator for BAE Systems RAD750 Microprocessors
CodeRunner JTAG Emulator
Designed for the most hazardous high radiation environments, the BAE Systems RAD750 radiation hardened PowerPC microprocessor is the most advanced processor offered to the space community. From the Mars Reconnaissance Orbiter to the Curiosity Rover, the RAD750 microprocessor has proven time and again to lead the industry in quality, performance, and cost.
