G12x Slide Mount
Virginia Panel Corporation (VPC)
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
- G12x - 18 Module Solution
- G12x Slide Mount
- G12x Tabletop
- Enclosure, G12x, Front Mount, 6"x18"x12"
- Enclosure, G12x, Front Mount, Sloped
- ITA, G12x, Front Mount, 18 Module
- Protective Cover, G12x, ITA, Aluminum
- Protective Cover, G12x, Receiver
-
product
Receiver, G12x, 18 Module, with 20" Platform, for Slide Mount
310104385
The 20” G12x Receiver provides rack mounting and tabletop mounting options. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
product
Receiver, G12x, 18 Module, 20" Platform, w/ Ext Handle for Slide Mount (slide kit required)
310104457
This G12x Receiver is slide-mounted with a 20” platform that supports up to 180lbs. or up 350 lbs. when used with optional leg kit. The G12x is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull-down for a reliable connection every time. The handle is extended 6" and can be rotated in 90 degree increments. The G12x is rated up to 20,000 cycles.
-
product
Dual Chassis Mounting Kit, For Mounting 2 PXI Chassis Together
310113605
This kit can be used with any VPC system. Includes 2 mounting flanges to attach 2 NI PXI-1045,1044 or PXIe-1075, 1065 chassis together.
-
product
Rack Extender Kit, G12x, 1.5" Deep
310113519
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12x Receivers.
-
product
Gap Cover, G12/G12x, Rack Mount
310113433
Gap cover for use with rack mounting G12/G12x Receivers. The gap cover is not required if a rack extender kit is used.
-
product
Rack Extender Kit, G12x, 1.5" Deep
310113519
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12x Receivers.
-
product
ITA, G12, Front Mount, 12 Module With Protective Cover
410104322
The G12 ITA can be used with all G12 Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
ITA, G12x, Front Mount, 18 Module
410104474
The G12x ITA can be used with all G12x Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
Enclosure, G12, Front Mount, 4"x18"x12"
410112665
The G12 ITA enclosure is made of aluminum and features a hinged cover plate with 1/4 turn hardware and provides easy access to the ITA wiring.
-
product
Enclosure, G12, Front Mount, 4"x18"x12", For Discrete Wiring
410112739
Enclosure, Part # 410 112 739 gives you the ability to discrete wire to your UUT with secure strain relief provided by the cable clamps located on the back end. Once the cable clamps are open, you can remove the stiffener bar and install or remove cables without unplugging patchcords from the assembly.
-
-
product
Enclosure, G12x, Front Mount, 6"x18"x12"
410112849
The G12x ITA enclosure is made of aluminum and features a hinged cover plate with 1/4 turn hardware and provides easy access to the ITA wiring.
-
product
Enclosure, G12x, Front Mount, 6"x18"x12", For Discrete Wiring
410112856
This enclosure gives you the ability to discrete wire to your UUT with secure strain relief provided by the cable clamps located on the back end. Once the cable clamps are open, you can remove the stiffener bar and install or remove cables without unplugging patchcords from the assembly.
-
-
product
Keyboard Tray Kit, Slide Configuration, Keyboard With Touchpad Mouse Included
310113439
The Keyboard Tray Kit is used with the S6, G12 & 9025TR in slide configurations. The keyboard with touchpad mouse connects to the computer’s USB port.
-
product
Keying Pin Kit, Receiver/ITA
310118112
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
product
Adjustable Leg Kit For The 20" Platform, 27 - 36", Supports 350 Lbs.
310113566
The legs are designed to alleviate added weight from your enclosure by giving the platform extra support. Each kit includes two legs which have a mounting block for attachment to the receiver platform. The legs are adjustable in height from 27 inches to 36 inches in 1 inch increments using the telescoping feature of the legs. The leveling guide can be adjusted to exact heights between the 1 inch increments.
-
product
Protective Cover, G12x, Receiver
310113518
The Receiver Protective Cover prevents damage to your modules and contacts and keeps your test system in proper working order.
-
product
Protective Cover, G12x, ITA, Aluminum
410112857
The G12x Aluminum ITA Protective Cover attaches securely to your ITA for easy and effective protection of contacts and modules. The cover snaps into place and enables smooth maneuverability of the ITA and enclosure over tables and other surfaces.
-
product
Dual Chassis Mounting Kit, For Mounting 2 PXI Chassis Together
310113605
This kit can be used with any VPC system. Includes 2 mounting flanges to attach 2 NI PXI-1045,1044 or PXIe-1075, 1065 chassis together.
-
product
Receiver, G12x, 18 Module, with 20" Platform, for Slide Mount
310104385
The 20” G12x Receiver provides rack mounting and tabletop mounting options. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
product
20" Slide Kit, Fits 18"-22" Deep Racks
310113409
Slide kits include a mounting bracket kit, slides and hardware. Choose your slide kit based onthe distance from rail to rail and verify that the slides will not interfere with the rack enclosure. Each kit will support 180 lbs.
-
product
24" Slide Kit, Fits 22"-26" Deep Racks,Supports 180 Lbs.
310113410
Measure rack depth between mounting rails to determine the slide mounting kit that fits the rack. An extender block kit is available for mounting to racks with recessed rails.
-
product
30" Slide Kit, Fits 28"-32" Deep Racks, Supports 180 Lbs.
310113411
Measure rack depth between mounting rails to determine the slide mounting kit that fits the rack. An extender block kit is available for mounting to racks with recessed rails.
-
product
28" Slide Kit, Fits 26"-30" Deep Racks, Supports 180 Lbs.
310113451
Measure rack depth between mounting rails to determine the slide mounting kit that fits the rack. An extender block kit is available for mounting to racks with recessed rails.
-
product
36" Slide Kit, Fits 34"-38" Deep Racks, Supports 180 Lbs.
310113500
Measure rack depth between mounting rails to determine the slide mounting kit that fits the rack. An extender block kit is available for mounting to racks with recessed rails.
-
product
Protective Cover, G12, Receiver
310113402
The Receiver Protective Cover prevents damage to your modules and contacts and keeps your test system in proper working order.
-
product
Enclosure, G12X, Front Mount, 14.75" Depth
410112122
Includes a hinged top cover. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
