6TL Engineering
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems. Thanks to this technology, the standardization of the test system comes intrinsically with the integration process, and the result will be a flexible, re-usable and reliable system that will drastically differenciate from former test investments.
- 34 937 270 074
- 34 937 253 576
- info@6tlengineering.com
- C. Solsonès, 87-89 Pol. Ind. Pla de La Bruguera
Castellar del Vallès, 08211
Spain
Filter Results By:
Products
Applications
-
product
EOL RF Functional Test
AS652
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
product
Ethernet to CAN Bus Gateway
YAV90090
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
product
Exchangeable Cassette Kit for 6TL36 Faraday Chamber
AN134
Exchangeable plates for RF applications. (Use with RF Kit, P/N AN133)).DUT maximum dimensions: 340 x 350mm
-
product
Faraday Chamber for RF
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
Fixture ID, Cycles Counter Laser Sensor
AR313 & AR706
The AR313 module contains in its editable registers the fixture identification numbers, as well as the mechanical parameters of the product, allowing the safe automation of the set-up of the machine. It also has two counters for the test cycles carried out.
-
product
Fixture Kit for 6TL34
AG588
Stopper kit included YAVCANCON2 for fixture identification not included
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Flipper
H71007100
Easy operator access for loading and unloading the DUT, thanks to the flip operation performed by the Flipper module. Combined test (Hipot, ICT & Funcional) Rack&stack module for 19 inch frame 6 U height (266,7 mm 10.5”) Pushing force up to 900N (more than 400 needles @2N) Power supply 230V 50-60 Hz. Compressed air not required High dynamics and precission CNC servocontroller PCB areas up to 232x358mm. Bigger areas available under request. Interchangeable cassette for upper bed of nails or actuators
-
product
High Current Power Switching
YAV90CIN
12 Independent SPST relays Switching up to 8A 250Vac 12 current measurement channels 8x Sense connections General inhibit input CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Isolated 24Vdc/+- 15V 200mA Active Probe Power Supply
H62005200
2×4 Terminal points for 24Vdc2×3 Terminal points for 15Vdc
-
product
ITA 192-Pin PCB Adapter to 3x IDC 64
YAV90Q06
3x 2 IDC 64 x 1000mmCables set J6200560 (Order Separately)
-
product
ITA Terminal Blocks
YAVTB000
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
product
Linear Voltage Regulator
YAV90075
This module is ideal to cover power supply needs in fixture proyects. For voltages up to 20V, through two regulable channels. With an minimum input level of 2.7V and a maximum of 20V, has only 340mV of drop voltage. The maximum current supplied for each channel is 1.5A.
-
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
-
Columbia Elektronik AB
COLUMBIA ELEKTRONIK AB is an expert organisation delivering complete test fixturing solutions to the Nordic electronics industry. Having pioneered the Swedish, Norwegian, Finnish and Danish markets back in 1977 we have today an absolute leadership in fixturing and test technology and enjoy a solid, major share of the market. We cover the whole spectra with testsystems, testfixtures, mass interconnect solutions and both hardware and software support and services. We design and produce both our own and vendor delivered testfixtures and mass interconnect solutions for functional and in-circuit test of electronic products and assemblies from component and PCB level to subassemblies and finished products. Columbia excels in all modern fixturing technologies – be it vacuum actuated, mechanical or pneumatic – applied to stand-alone, tester-integrated or inline fixtures.
