NI

product

PXIe-2738 , 256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module

782835-38

NI

782835-38 - NI

256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module—The PXIe‑2738 is a high‐density 8x32 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.

product

cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis

781497-01

NI

781497-01 - NI

1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.

product

PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver

785585-02

NI

785585-02 - NI

The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.

product

acA2000-340km, Monochrome Camera Link, 2 MP, 340 FPS Area Scan Camera

782142-01

NI

782142-01 - NI

The acA2000-340km is a Monochrome Basler Ace Camera Link Camera with a 2 MP resolution and a maximum image acquisition speed of 340 frames per second. … The acA2000-340km uses a CMV2000 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.

product

MXI-Express Cable, Gen 1 x1, Copper, 1m

779500-01

NI

779500-01 - NI

MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.

product

NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO

782705-01

NI

782705-01 - NI

The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).

product

PCIe-8239, 4-Port, GigE Vision Frame Grabber Device

787790-01

NI

787790-01 - NI

The PCIe-8239 features Power-over-Ethernet (PoE) technology. It provides optimized performance of high-resolution and high-frame rate cameras through the combination of independent Gigabit Ethernet ports and the high-performance GigE Vision driver software. PoE reduces the need for additional external power supplies by powering cameras over the Ethernet bus, which simplifies system design and cabling complexity.

product

PXIe-5442, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 256 MB, PXI Waveform Generator

780109-02

NI

780109-02 - NI

PXIe, 43 MHz Bandwidth, 16-Bit Onboard Signal Processing, 256 MB, PXI Waveform Generator—The PXIe‑5442 is a 43 MHz arbitrary waveform generator capable of generating user-defined, arbitrary waveforms, standard functions including sine, square, triangle, and ramp, as well as signals that require onboard signal processing. Some of these signal processing operations include FIR and CIC interpolation filters, digtal prefilter gain, numerically-controlled oscillator, and I/Q mixing for quadrature digital upcoversion. The PXIe‑5442 also features advanced synchronization and data streaming capabilities.

product

PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer

781774-03

NI

781774-03 - NI

Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.

product

SHC68M-68F-RMIO, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable, 2m

189588-02

NI

189588-02 - NI

68-Pin Male VHDCI to 68-Pin Female D-SUB, Shielded Multifunction Cable - The SHC68M-68F-RMIO Cable, sometimes referred to as SHC68-68-RMIO, connects to the terminal block of a multifunction reconfigurable I/O (RIO) device. The SHC68M-68F-RMIO Cable is offered in different lengths.

product

sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module

780539-01

NI

780539-01 - NI

Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.

product

PXI-7842, Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module

780338-01

NI

780338-01 - NI

Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7842 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.

product

NI-6587, 1 Gbit/s, 20 LVDS-Channel Digital Adapter Module for NI FlexRIO

781702-01

NI

781702-01 - NI

1 Gbit/s, 20 LVDS-Channel Digital Adapter Module for NI FlexRIO—The NI-6587 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 20 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6587 can sample digital waveforms at up to 1 GHz and includes support for common LVDS voltages.

product

VB-8054 , 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument

785037-04

NI

785037-04 - NI

4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.

product

Temperature Sensor

NI

NI

The Temperature Sensor works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for Temperature Sensors and acquire synchronized temperature data.